Show all posts by user
Page 2 of 3
Pages: 123
Results 31 — 60 of 70
temperature port gone on the arduino.
de port was 36 degree and not moving up or down.
i re rout the port and it works now but how is it possible.
by
michel pet
-
RAMPS Electronics
keyped. - 11 years ago
is it possible to get support for this keypad controller in repetier???.
by
michel pet
-
Repetier
the contrast is automatic in the lcd a have.
by
michel pet
-
Repetier
how to wire it up.
by
michel pet
-
Repetier
after a lot of problems i have it running OK now.
i think we need drawing to ex plane how to wire it up.
by
michel pet
-
Repetier
hier een filmpje van de eerste test en ja wel het werkt erg goed nu een goed ontwerp maken met de motor en bij aan.
by
michel pet
-
Dutch User Group - Archive
temperature feedback is changing and keeps going up.
i installed a new mosfet and it works OK now.
by
michel pet
-
RAMPS Electronics
when i plug in the power the extruder head starts heating up and doesn't stop no control at al is the mosfet broken???.
its working now.
by
michel pet
-
RAMPS Electronics
repetier is nog nieuw en in ontwikkeling maar werkt wel erg lekker.
het gaat hier om pc soft ware en voor arduino ff op letten dus wat je wil hebben.
al had ik vandaag wat problemen dat het hele zakie er uit klapt reden nog geen id werkte voor heen prima.
by
michel pet
-
Dutch User Group - Archive
de y as aan gepast en werkt nu op 1 nema 23 motor.
de armen worden ook aan gepast is me net ff te zwak.
alu plaat 5mm is besteld voor het te verwarmen bed.
2 de extruder kop is nu in gemaakt en werkt ook goed met een 0.35mm .
druk in de weer tot tot.
by
michel pet
-
Dutch User Group - Archive
opgelost de temp sensor at niet helemaal goed en de kop zelf werd dus flink heter dan verwacht.
by
michel pet
-
Dutch User Group - Archive
ik zit met het volgende als ik me kop op warm komt de pla er al uit onder het op warmen en als ik wil gaan printen is de kop dus leeg.
nu zet ik de extruder motor aan en dan is het er weer maar druipt dan snel weer leeg voor dat ik op het punt van het printen kom.
ik het al geprobeerd om op 180 graden te printen maar dan werkt het niet ok en bij 185 graden is de kop te snel leeg.
de eerste laag
by
michel pet
-
Dutch User Group - Archive
is it possible to make a feed bar so we can real time go up or down and set the speed we need in real time.
by
michel pet
-
Slic3r
http://www.youtube.com/watch?v=NypmwFqmamE&hd=1
NypmwFqmamE&hd=1
geting beter 300mm s but stil not ok.
by
michel pet
-
RAMPS Electronics
this is my home build big print.
first test x and y .
ramps1.4.
arduino1280
4.8ncm motor.
sd card.
24 volt dc
now i have to vigor out Ho to setup the software its to fast.
http://www.youtube.com/watch?v=E4RFc9Zh4sQ
by
michel pet
-
RAMPS Electronics
http://www.youtube.com/watch?v=E4RFc9Zh4sQ
eerste test run al stond het nog niet goed ingesteld.
20mm blokje.
by
michel pet
-
Dutch User Group - Archive
i have problems with the com port speed its not stable.
i have tried several speeds but still not found a stable one.
also not all pc cq laptops can run all the speeds.
i think 115200 is a speed al pc and laptops can handel.
the program is great and all the thing we need are there.
by
michel pet
-
Firmware - experimental, borrowed, and future
het deel wat beweegt loop soepel en is goed gelagerd en weegt niet veel.
ik heb de motoren in een testopstelling aan de praat nu nog af stellen kwa stroom en dat valt niet mee heb ze nu rond de 60 graden en loopt nog steeds goed zonder koeling wel met koel blokken er op.
ik kreeg de sd kaart niet aan de praat in replicatorg en ben over gestapt naar repetier- host en daar werkt het wel en moet ze
by
michel pet
-
Dutch User Group - Archive
Page 2 of 3
Pages: 123