Gjutna delar låter coolt och helt klart något jag hade velat ha på mina skrivare om jag kunde Ska följa ditt bygge ser mycket bra ut!by logicron - Sweden, Gothenburg RepRap User Group
Mycket nice printer! Var får du dina delar från? Gillar in Another big printer! Ska titta närmre på din tråd Annars kan jag tipsa om www.reprappro.me för byggsatser och reservdelar!by logicron - Sweden, Gothenburg RepRap User Group
Glömde skriva hemsidan RepRapPro.Me eller RepRapPro.Seby logicron - Sweden, Gothenburg RepRap User Group
I am fairly sure it is the baud rate , i am switching between a Melzi and RAMPS all the time and i get the same problem when i use my Arduino Mega, Change the baud rateby logicron - Reprappers
It seems very strange that the first layer it is extruding well and then not anymoreby logicron - Mendel90
Yea i can se the first layer seems to work well is your extruder skipping ? seems like it because plastic is coming out but not i a good wayby logicron - Mendel90
No problem write how it goes Also buy some acetone (without oil) to clean surface in between prints, also works nice for meby logicron - Mendel90
Try the paper thing to measure the distance between heatbed and nozzle and get some kapton tape for me it works really goodby logicron - Mendel90
Allright let me try to answer: 1. It seems like you need to centre your 3d printer. 2. What material are you using? PLA or ABS?, are you using Kapton tape or what is your print surface? 3. this seems to be because it is not sticking to surfaceby logicron - Mendel90
My first printer was a i3 and i loved it! It is a good start and it has a good price! I also have the RepRapPro Mono Mendel that i also highly recommendby logicron - Reprappers
For me it sounds like your y and x is skipping steps, the the belt tight enough?by logicron - Printing
Sorry not that i know of, what MK7 extruder do you have?by logicron - General
I have a webshop that sells to Holland Check it out! [3dprinterstore.tictail.com]by logicron - Dutch User Group - Archive
There is bigger sizes but i believe 214 x 214 is the most popular. I have also been able to print PLA without a heatbed , so like that you can make a huge glass plate to print onby logicron - Reprappers
I use both MK7 and MK8 and have good results with both. What extruder do you want to make?by logicron - General
Try to switch the temp around and se if you get the same value. Rule out if the temp is defect or something elseby logicron - Reprappers
Hallå! Hur går det med bygget? Hade rekommenderat dig en J-Head och en Gregs Wade extruder. Men det är ett tag sen du postade , har du kommit vidare?by logicron - Sweden, Gothenburg RepRap User Group
Säljer nu dessutom PETG, HIPS, Trä, Strömledande, Flexible och Nylon! RepRapPro.Meby logicron - Sweden, Gothenburg RepRap User Group
En skåning till i Malmö Mono Mendel, och egen gjort skrivare baserad på Core XYby logicron - Sweden, Gothenburg RepRap User Group
Fick du fatt på någon som kunde skriva ut till dig?by logicron - Sweden, Gothenburg RepRap User Group
Hej Robert Kommer från Malmö men är mycket i London nu för tiden så det blir lite svårt att komma över till Trelleborg. Men hjälper dig gärna över Skype om jag kan! Skicka mig ett PMby logicron - Sweden, Gothenburg RepRap User Group
You can also run M302 command in pronterface and it will allow you to do a cold extrusionby logicron - Reprappers
Aluminium gives a great and even heat. But i have used both glass and mirrors with great resultsby logicron - Reprappers
Test your temp sensor, does it give a good value at room temp?by logicron - Reprappers
The normal size of this is usually 214mm x 214mm To heat is usually 180 C in my experience You can put some kind of wood part under it , this is usually done on the regular printers like the Prusa i3 Hope this helpsby logicron - Reprappers
It can give you errors and warnings also!by logicron - Reprappers
Ser ut som om du har en del erfarenhet med Mono, Tri, Huxley och Ormerod Kul att höra! var i Sverige befinner du dig? Ser att du kör stora nema stegmotorer vad är det för model på dem? Hade också haft samma nerkylning som du, nu har jag denna som riktar luftstömmen lite mer fokuserat. Ditt problem låter som kretskortet om allt annat testat, kan du se något fysiskt problem vid hot end kontakteby logicron - Sweden, Gothenburg RepRap User Group
Coolt att höra om fler Reprappare i Sverige. Hade gärnat joinat men bor i Malmö så det är en bit Men har startat en Google + sida för Svenska RepRap entusiaster för delning av kunskap och ideer kring RepRap 3D-skrivare! Hade gärna sett lite fler på sidan!by logicron - Sweden, Gothenburg RepRap User Group
Hej Staffan Gå in på RepRapPro.Me och ta en titt om det fortfarande är intressantby logicron - Sweden, Gothenburg RepRap User Group