Welcome! Log In Create A New Profile

General Mendel Topics

Prusa i2, Prusa i1, Prism, Sells, and other Mendel variants

Page 5 of 66 Pages:

3 456 7

Forum List New Topic RSS

	Views	Posts	Last Post
220V ac Heated Bed by Gaou	2,893	7	07/01/2016 11:24PM Last Post by bgkdavis
Opinions on Upgrades by DarkReeper	914	8	06/26/2016 05:30PM Last Post by dc42
Best extruder for Reprap Mendel by axeldk	1,804	11	06/26/2016 05:24PM Last Post by dc42
RPP Mendel 3 Extruder's Small Gear by Gaou	777	3	06/26/2016 11:36AM Last Post by Gaou
material not coming out of nozzle by zatix	882	3	06/25/2016 04:15AM Last Post by deckingman
Looking for RPP Mendel 3 Plans by Gaou	860	7	06/24/2016 02:53AM Last Post by bgkdavis
Any RepraPro mendel users here by Gaou	1,264	22	06/20/2016 07:14AM Last Post by bgkdavis
Y axist stop at 180 mm by Jahaziel Morales	768	2	06/15/2016 02:49AM Last Post by Dust
Suddenly stopped printing by fractal5	946	1	06/08/2016 07:40PM Last Post by fractal5
Prusa i3 Z-axis noise when lowering by loxua	2,195	2	06/08/2016 11:54AM Last Post by stephenrc
Prusa i3 bed levelling - Marlin firmware (RAMPS 1.4) by ss002d6252	1,612	2	06/05/2016 01:24PM Last Post by stephenrc
stepper motor calibration by flavioc	1,184	4	06/03/2016 05:24AM Last Post by Downunder35m
Prusa i2 Z axis homing issue by flavioc	903	2	06/03/2016 01:14AM Last Post by flavioc
MAXTEMP error by Shieldudaram	859	2	06/02/2016 11:00PM Last Post by Dust
Mendel 3 Tri Coulor extruder drive instruction confusion by slackcub	796	4	05/29/2016 08:03PM Last Post by slackcub
End Stops and RAMPS 1.4 by ss002d6252	852	4	05/28/2016 11:54AM Last Post by Sanjaykray
Err: MINITEMP by osip7	1,359	2	05/28/2016 05:39AM Last Post by Dust
3D Stuffmakers Mendal gen 2 by juniormachinist	836	2	05/26/2016 02:03AM Last Post by Downunder35m
Schematics for printed parts? by Hypnofrogs	766	3	05/24/2016 12:12PM Last Post by blt3dp
Auto bed leveling working as it should? by fractal5	1,791	1	05/21/2016 12:50AM Last Post by fractal5
Regular irregularities (not only) on the surface... by c1480372	850	3	05/18/2016 04:32AM Last Post by c1480372
[HELP] Megatronics 3.0 motors not moving!! by Antoine13710	872	5	05/17/2016 10:20PM Last Post by Govahnator
Power supply for Prusa i2 by greenLeD111	716	2	05/16/2016 03:45PM Last Post by blt3dp
Z-Axis Noob Help by lifeinbeats	801	4	05/15/2016 11:07PM Last Post by MarkBot
Axes not moving properly by greenLeD111	1,068	8	05/15/2016 03:41PM Last Post by greenLeD111
Strange Marlin issue by SolderSucker	710	3	05/11/2016 11:48AM Last Post by jinx
Please, this is the 7th try, how to awoid this by Cannehag	1,028	13	05/08/2016 08:41AM Last Post by Origamib
Why the brim not same at right and left way by taratata	751	3	05/06/2016 09:18AM Last Post by Tinchus
Burned terminal on RAMPS 1.4 by rich1812	1,001	3	04/29/2016 03:37PM Last Post by bigaustin
Why are my prints going wrong ? by ss002d6252	836	4	04/29/2016 03:28AM Last Post by ss002d6252

Page 5 of 66 Pages:

3 456 7