Welcome! Log In Create A New Profile

RepRap Usergroup - Argentina

http://reprap.org/wiki/RUG/Argentina - Lista de proveedores, Reuniones, y ayuda al futuro RepRapper

Page 8 of 37 Pages:

6 789 10

Forum List New Topic RSS

	Views	Posts	Last Post
Preguntonta de ventilador.... by franco1600	468	4	04/08/2016 01:44PM Last Post by franco1600
[CONSULTA] Correa GT2 cerrada by ldcampana	746	3	04/06/2016 03:58PM Last Post by diegognavarro
Novato desesperado¡ by rafetalay	3,191	23	04/05/2016 04:07PM Last Post by rafetalay
Problemas de calibracion replikat m5 by rkD	762	3	04/05/2016 07:27AM Last Post by diegognavarro
Consultas de calibracion by franco1600	453	3	04/04/2016 11:58PM Last Post by qubotica
Problema para Calibrar Los motores paso a paso by morpheus1978	1,153	2	04/03/2016 01:19AM Last Post by morpheus1978
[REGALO/TRUEQUE] Mosfets para cama by Pointless	1,433	14	04/02/2016 09:34PM Last Post by [email protected]
reutilizar controladores de impresoras epson by [email protected]	1,214	7	04/01/2016 05:28PM Last Post by [email protected]
Datasheet de estos motores PaP de impresoras epson by lavp97	7,129	5	03/31/2016 01:11PM Last Post by lnscapola
Presentacion - Condorcoc corte Laser by condorcoc	1,023	2	03/29/2016 01:12PM Last Post by SinapTec
No guarda cambio en firmware by diter23	683	3	03/25/2016 11:50PM Last Post by diter23
Problema con infill. by diter23	468	2	03/23/2016 10:41PM Last Post by diter23
Consulta salidas I2c Ramps 1.4 by MCR	663	3	03/21/2016 07:59AM Last Post by MCR
Aporte. Mi solucion a la demora en calentar de la cama. by diter23	622	1	03/17/2016 01:35AM Last Post by diter23
Presentación y consulta. by diter23	544	6	03/17/2016 01:13AM Last Post by diter23
Presentación y consulta by guillote	417	2	03/11/2016 10:01PM Last Post by diegognavarro
Hola a todos, consulta. by acmeboy	1,449	9	03/11/2016 09:52PM Last Post by diegognavarro
Consulta sobre modelos de impresoras by nicoelaji	505	2	03/11/2016 11:57AM Last Post by hho032
Consulta compra Insumos by agumluna	552	1	03/01/2016 09:27PM Last Post by agumluna
Cama en corto by tikey	510	4	02/26/2016 07:00PM Last Post by Valvulin
Ayuda Final de carrera by abigliazzi	715	3	02/26/2016 04:32PM Last Post by abigliazzi
Lcd Prende pero no mueve motores ni nada by Padi	531	2	02/26/2016 02:20PM Last Post by Padi
cables quemados AYUDAA by Ferrari	735	12	02/25/2016 01:06PM Last Post by tikey
Presentacion y 1er (de muchas mas) Consulta SOFTWARE by ezequiel1090	574	4	02/24/2016 07:54PM Last Post by ezequiel1090
ABS y Cama Caliente si o si? by Sotnas	571	5	02/24/2016 06:25AM Last Post by hho032
PRoblema con el Extrusor...extraño... by morpheus1978	506	5	02/23/2016 10:35PM Last Post by Sotnas
Presentación y consulta by DrG	564	6	02/22/2016 01:03PM Last Post by DrG
Duda cama caliente by naufi	445	2	02/20/2016 06:38PM Last Post by diegognavarro
Tecnologia polyjet by nicoelaji	478	1	02/18/2016 03:21PM Last Post by nicoelaji
Nuevo avance de mi impresora 3D (nueva reprap) by rsc	440	2	02/15/2016 11:13PM Last Post by rsc

Page 8 of 37 Pages:

6 789 10