Welcome! Log In Create A New Profile

CoreXY Machines

http://reprap.org/wiki/CoreXY

Page 19 of 20 Pages:

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Why are max endstops disabled in marlin? by NathanaelXYZ	9,797	18	05/24/2015 07:59AM Last Post by alan richard
	Quickhome on Corexy by ruggb	944	7	05/19/2015 11:49PM Last Post by ruggb
	Help on custom big bot, bad cylinder, calibration issue or what? by execcr	1,193	10	05/14/2015 02:31AM Last Post by execcr
	quickhome issue by ruggb	670	1	05/08/2015 07:50PM Last Post by ruggb
	Controller for XY-Stage - parameters and behaviour? by Elmi	813	4	05/01/2015 05:19AM Last Post by hairykiwi
	Would this work? by Dave_robinson_022	1,335	9	04/28/2015 10:42AM Last Post by LarsK
	Sunday Print Challenge runs until Tuesday! by AndrewBCN	773	1	04/27/2015 04:00AM Last Post by AndrewBCN
	CoreXY and CoreXZ support for Duet electronics by dc42	2,878	18	04/26/2015 03:43PM Last Post by patrickrio
	Delays required in XY-Stage controller by Elmi	929	1	04/25/2015 10:55AM Last Post by Elmi
	What type of Hiwin! by mdcompositi	3,260	17	04/21/2015 11:55PM Last Post by patrickrio
	Another V-Slot CoreXY Printer by sdavi	15,709	27	04/17/2015 01:57PM Last Post by Hexag
	Not moving in negative direction..neither X nor Y by nipunsadvilkar	1,322	2	04/11/2015 01:51PM Last Post by alan richard
	Fishing string by ntar827	1,034	6	04/08/2015 08:01PM Last Post by SydneyDesigner
	CoreXY printer slowing down near 0 speed by PropellerHat	1,609	23	03/27/2015 07:17AM Last Post by PropellerHat
	Building Core XY Printer: need help deciding on what built by J.A.C.	14,451	26	03/26/2015 09:14PM Last Post by alan richard
	endstops for corexy? physical or firmware based? by pushthatbolder	1,448	5	03/15/2015 10:00PM Last Post by alan richard
	Print starts promisingly, then drifts over max pos by PropellerHat	910	4	03/15/2015 09:08PM Last Post by alan richard
	Core XY assembly suitable for XY plotter by nipunsadvilkar	1,741	3	03/10/2015 04:32AM Last Post by Zavashier
	my corexy by mdcompositi	1,515	6	03/05/2015 11:05AM Last Post by enricodare
	Introducing the Slot Bot! by runninfarmer	1,972	9	03/05/2015 09:04AM Last Post by Zavashier
	Core XYZ? by Echo Bravo	7,864	7	02/25/2015 09:15PM Last Post by nicholas.seward
	Advice on printer sizing and makerslide by rocketwiz	1,075	5	02/22/2015 06:44PM Last Post by rocketwiz
	Reduce Bed Shake by jtoombs	1,815	2	02/22/2015 01:42PM Last Post by Zavashier
	CoreXY and Duet+RepRapFirmware by UkIan	1,984	6	01/27/2015 06:49PM Last Post by dc42
	Design Options CoreXY by Lorcan	1,706	7	01/27/2015 11:10AM Last Post by Zavashier
	Help with first time build by ivinder	1,027	5	01/23/2015 05:02PM Last Post by runninfarmer
	Not quite CoreXY but Sli3DR source files are released by richrap	5,525	8	01/23/2015 12:21PM Last Post by cablemite
	Openbeam CoreXY in Construction by RepRot	5,661	13	01/22/2015 04:53PM Last Post by alexella
	CoreXYL(aser) setup by Ohmarinus	3,597	6	01/19/2015 03:51PM Last Post by runninfarmer
	Belt configuration by jtoombs	2,278	13	01/17/2015 09:32AM Last Post by gforce1

Page 19 of 20 Pages: