Welcome! Log In Create A New Profile

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests...

Page 75 of 98 Pages:

73 747576 77

Forum List New Topic RSS

	Views	Posts	Last Post
[1.1.8] G26 Pattern didn't finish and then lowerd the Z axis by Gazit6	362	2	03/11/2018 07:48PM Last Post by Roxy
Does marlin BEEP when 3d print is done ? by windchime	17,229	6	03/09/2018 01:21AM Last Post by Melty
Problem with OLED (LCD) 2004 with HDD44780 controller by Nitec0re	513	1	03/08/2018 06:25PM Last Post by Nitec0re
Circular moves slows down as I increase print speed. by j0achim	402	1	03/08/2018 05:08PM Last Post by j0achim
Marlin 1.1.8+ M420 S1 required after G28 by DaHai8	11,867	5	03/08/2018 02:15PM Last Post by ruggb
Inductive auto level Marlin1.1.8 by jaded	606	6	03/08/2018 08:52AM Last Post by ruggb
Calculating Steps/mm by 3DNublet	21,150	5	03/07/2018 05:57PM Last Post by 3DNublet
Delta: Determine delta-radius, bed tilt, and bed imperfections all with one test? by jemenake	792	2	03/07/2018 04:05PM Last Post by jemenake
Marlin Turn off heaters when Z homing and bed leveling by noel841106	3,809	3	03/07/2018 03:29PM Last Post by noel841106
Printer locks up after moving axes by Livid	383	1	03/07/2018 01:27PM Last Post by Livid
Problem with Marlin upload by zurferjoe	1,582	7	03/05/2018 07:26AM Last Post by zurferjoe
Changing the direction of a motor by v1talogy	1,501	1	03/05/2018 07:23AM Last Post by v1talogy
Proximity Sensor problems by nick9one1	1,174	3	03/04/2018 04:55AM Last Post by nick9one1
What happens to z-offset with autoleveling? by bcsteeve	8,167	3	03/01/2018 06:59PM Last Post by Thinkyhead
Z_SAFE_HOMING - X speed to bed center? by penkerton	755	2	03/01/2018 06:30PM Last Post by Thinkyhead
Protect public-access printer from use except by assigned computer by paulr	375	5	02/28/2018 12:18AM Last Post by Roxy
Setting default feedrate / printspeed by LittleNyanCat	1,630	2	02/25/2018 10:14AM Last Post by obewan
Printer not homing? by leonnisae	464	6	02/24/2018 09:07PM Last Post by Dust
Steppers go to sleep after 20 sec by RC-CnC	1,172	7	02/24/2018 05:28PM Last Post by RC-CnC
Disabling M105 by Sundog	448	1	02/23/2018 12:25PM Last Post by Sundog
UP/DOWN buttons instead of rotary encoder for display controller by pit34	1,409	1	02/23/2018 05:42AM Last Post by pit34
MKS Gen v1.4 -- cooling fan won't run by papilio	4,147	9	02/22/2018 04:38PM Last Post by papilio
Ramps 1.4 Marlin 1.1.8 2 Hotend by Kleinz1971	605	1	02/19/2018 04:53PM Last Post by Kleinz1971
G1 lines without the G1 by Sundog	409	7	02/14/2018 07:43PM Last Post by Sundog
"Inverted" ABL Correction Matrix? by bcsteeve	1,297	7	02/13/2018 01:09PM Last Post by bcsteeve
Which is the difference betwen Z_offset and in the Mesh Bed Level and Fade_height in the Bilinear leveling? by Aldebaran94	487	1	02/13/2018 12:11PM Last Post by Aldebaran94
Marlin 1.1.8 & Delta + Probe - Bilinear Z-Offset Adjustment? by DaHai8	1,184	1	02/13/2018 09:54AM Last Post by DaHai8
Marlin118 ABL G29 Help Needed by Cathelest	646	8	02/10/2018 08:33PM Last Post by Roxy
IDE error when trying to upgrade by nkuck	914	2	02/10/2018 12:29PM Last Post by nkuck
Marlin to Sav MK1 by kapperi	606	11	02/08/2018 02:17PM Last Post by kapperi

Page 75 of 98 Pages:

73 747576 77