Welcome! Log In Create A New Profile

Advanced

Duet

Duet is the Arduino Due Compatible RepRap Electronics 
Subject Views Posts Last Post

Extruder motor going both forward and backwards on extrude

by ElmoC
827 5 06/04/2017 08:39AM
Last Post by ElmoC

Storing Calibration?

by clearlynotstefan
442 2 06/03/2017 03:50AM
Last Post by dc42

Firmware 1.18.1 and Heater Faults

by DRTak
2,341 12 06/02/2017 01:23PM
Last Post by dc42
This topic has been moved.

Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC

by Italia
    This topic has been moved.

Duet Wifi, two drivers for one 8 wire motor?

by M;kko
365 2 05/29/2017 02:20AM
Last Post by dc42

Mechanical switch for z probe

by chris33
882 10 05/25/2017 05:19PM
Last Post by chris33

M997 S2

by 3D-Print
432 2 05/24/2017 02:26AM
Last Post by dc42

M572 pressure advance for Diamond hotend?

by o_lampe
427 5 05/23/2017 06:17AM
Last Post by dc42

Fan selection?

by clearlynotstefan
874 4 05/23/2017 02:18AM
Last Post by drmaestro

PanelDue STOP not the same as DWC Emergency Stop?

by PDBeal
365 3 05/22/2017 04:12PM
Last Post by dc42

Firmware upgrade

by joestefano
519 9 05/17/2017 04:18AM
Last Post by dougal1957

Fan short!

by clearlynotstefan
368 6 05/14/2017 01:33AM
Last Post by clearlynotstefan

Raspberry Pi as display

by Napalm1432
790 7 05/12/2017 02:26AM
Last Post by o_lampe

just a quick connector question

by chris33
380 3 05/07/2017 04:21PM
Last Post by dc42

(small) Feature request

by unromeo21
406 20 05/07/2017 08:06AM
Last Post by roboprint

Duet 0.6 Burnt EO Heater Ground Now No Web Control Access

by DRTak
400 5 05/05/2017 11:47PM
Last Post by DRTak

Suggested Mosfet for Duet 0.8.5

by Nylkos
883 2 05/02/2017 05:11PM
Last Post by dc42

DUET with IR sensor

by selva_tvi
766 4 05/02/2017 05:00PM
Last Post by dc42

Panel Due brightness control

by JuJuDelta
384 5 04/30/2017 01:29PM
Last Post by JuJuDelta

Probe triggered and don't stop

by DeathmannX
962 7 04/27/2017 12:35PM
Last Post by ElmoC

S3D skirt/brim with M572 active

by unromeo21
435 1 04/25/2017 03:37PM
Last Post by unromeo21

Different motor temperatures in serial connection

by drmaestro
345 4 04/25/2017 03:03AM
Last Post by dc42

Dual extrusion with Single extruder

by selva_tvi
601 3 04/24/2017 01:46AM
Last Post by selva_tvi

Edit heightmap.csv? [Bug?]

by o_lampe
681 6 04/23/2017 03:40PM
Last Post by dc42

Upgrading to PT100

by drmaestro
467 4 04/23/2017 03:31PM
Last Post by dc42

Power failure, Print pause - Resume

by selva_tvi
1,392 6 04/23/2017 05:02AM
Last Post by dc42

Duet stopped mid print, doesn'T work anymore..... sad smiley

by drmaestro
519 10 04/21/2017 05:08PM
Last Post by dc42

Question for DC42

by lolocaledo
491 8 04/21/2017 04:59PM
Last Post by dc42

external sd/usb slot

by Napalm1432
321 4 04/21/2017 04:57PM
Last Post by dc42

Setting Z offset for printing

by drmaestro
9,962 7 04/17/2017 02:58PM
Last Post by dc42