Re: P3steel - toolson edition 02. February 2016 12:04 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 838 |
Re: P3steel - toolson edition 02. February 2016 15:50 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 298 |
Re: P3steel - toolson edition 02. February 2016 16:19 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 838 |
Re: Er lebt! Er lebt!! 02. February 2016 18:42 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 63 |
Re: Er lebt! Er lebt!! 03. February 2016 03:12 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 1.720 |
Re: P3steel - toolson edition 04. February 2016 11:37 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 10 |
Re: P3steel - toolson edition 05. February 2016 06:35 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 174 |
Re: P3steel - toolson edition 05. February 2016 12:28 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 10 |
Re: Er lebt! Er lebt!! 05. February 2016 12:36 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 556 |
Re: P3steel - toolson edition 05. February 2016 12:47 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 556 |
Re: P3steel - toolson edition 05. February 2016 13:05 |
Registrierungsdatum: 10 Jahre zuvor Beiträge: 4.977 |
Triffid Hunter's Calibration Guide | --> X <-- Drill for new Monitor | Most important Gcode. |
Re: P3steel - toolson edition 05. February 2016 13:11 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 174 |
Re: P3steel - toolson edition 05. February 2016 13:15 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 214 |
Re: P3steel - toolson edition 06. February 2016 17:33 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 214 |
Re: P3steel - toolson edition 06. February 2016 17:56 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 14 |
Re: P3steel - toolson edition 06. February 2016 18:57 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 1.720 |
Re: P3steel - toolson edition 07. February 2016 09:55 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 174 |
Re: P3steel - toolson edition 07. February 2016 10:02 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 1.720 |
Quote
Link83
... und auf einmal der lüfter vom netzteil angeht und das lauteste am gerät ist. TOP!
Re: P3steel - toolson edition 07. February 2016 10:15 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 174 |
Re: P3steel - toolson edition 07. February 2016 10:55 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 66 |
Re: P3steel - toolson edition 07. February 2016 11:00 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 1.720 |
Re: P3steel - toolson edition 07. February 2016 11:02 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 214 |
Re: P3steel - toolson edition 07. February 2016 11:19 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 556 |
Re: P3steel - toolson edition 07. February 2016 11:20 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 214 |
Re: P3steel - toolson edition 07. February 2016 12:31 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 556 |
Re: P3steel - toolson edition 07. February 2016 12:41 |
Registrierungsdatum: 11 Jahre zuvor Beiträge: 214 |
Re: P3steel - toolson edition 08. February 2016 14:23 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 111 |
Re: P3steel - toolson edition 09. February 2016 15:31 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 55 |
Quote
Mr.Coffee89
Es kommt auf dein Ramps drauf an... Gibt da viele Versionen, teils sehr komische Sachen..
RAMPS 1.4 Notes: If you remove all jumpers for MS1+MS2+MS3, then the SilentStepStick driver will be in 1/16 spreadCycle mode (CFG1=GND, CFG2=open, CFG3=open), because there is a pull-down resistor on MS1 on the RAMPS. But if you have not an original RAMPS 1.4, then your schematics can be different and you have to check the MS-Pin configurations on you board.
Hier steht alles: [github.com]
Re: P3steel - toolson edition 09. February 2016 16:14 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 838 |
Re: P3steel - toolson edition 09. February 2016 18:29 |
Registrierungsdatum: 9 Jahre zuvor Beiträge: 1.720 |