Show all posts by user
General discussions. For specific printers / electronics / fabrication methods / softwares, please see other sections.
Re: x axis carriage 9mm bearing not free - 10 years ago
FWIW I replaced the 9mm X-runner bearing by a 10mm (623ZZ) bearing today, and that finally resolved the problem I had with a sagging print head.by dc42 - Ormerod
Re: Network connection - 10 years ago
I was able to connect over Ethernet using firmware that I downloaded on 20/12, so I think it must be have been the 17/12 firmware If you can ping it, then the Ethernet connection must be working and you should be able to connect. A few suggestions: - Have you checked that you really are pinging the Duet, i.e. the ping fails if you disconnect the cable or turn the Duet off? - Are you using Chromby dc42 - Ormerod
Z axis homing and bed plane compensation issue: diagnosis & solution - 10 years ago
I was having a problem with Z axis homing and bed plane compensation. I set up the G32 command and automatic bed plane compensation coordinates as instructed. Before printing I home all axes and then run the bed plane compensation. But when I came to print, there were issues with distance between the nozzle and the bed. On one occasion, the nozzle was touching the bed and at least the first 2 layby dc42 - Ormerod
Re: Invalid G Code - 10 years ago
1. Did you update the firmware to latest, i.e. as of 2 days ago? 2. I use the automatic bed plane compensation, so I've never tried the G30 command.by dc42 - Ormerod
Re: Network connection - 10 years ago
I find that I need to power up the Duet, and start trying to connect with Chrome within a few seconds. The first few attempts are unsuccessful because the Duet isn't ready, but after a few tries it connects. Occasionally I find it won't connect, and I have to power the Duet down and start again. Alternatively: power the Duet up, start pinging it, and as soon as I get a successful ping, connect wby dc42 - Ormerod
Re: What is RepRappro policy on self-repair of Duet boards? - 10 years ago
I've removed those resistors, replaced them with new ones in the correct orientation, and added the 5VEN jumper. So now the board works with ATX power alone. I'm getting 4.93V pin the +5V line. However, now I hear that another mod is needed, which is to solder the tabs of the USB connector to the board. Before I dismantle the unit again to do that mod, are there any other inspections or mods toby dc42 - Ormerod
Re: some pics of Ormerod prints - 10 years ago
Thanks! What slick3r parameters do you recommend then?by dc42 - Ormerod
Re: Heat Settings - 10 years ago
The recommendation for Ormerod printing with PLA seems to be 65C and 205C. But these are normally set by the gcode file you are printing.by dc42 - Ormerod
Re: Broken micro USB socket - 10 years ago
I would hope that your board will be covered under warranty - it sounds like a manufacturing defect to me. In the meantime, I suggest you try to get Ethernet working. Preferably, plug it into your router. If like me you have it connected to a computer that is wirelessly connected to the router, then you need to bridge the wired and wireless network connections on the computer. When you have sorteby dc42 - Ormerod
Re: Strange behaviours - 10 years ago
Probably not related to problem #2, but I spotted a bug in the firmware. When processing the G10 command, there is no range check on the P parameter. As a result, if you pass any parameter other than -1 (which would set the bed temperature) or 0 (to set the extruder temperature), memory will be corrupted.by dc42 - Ormerod
Re: X axis - position problem - 10 years ago
Is there any chance that your X-belt is slipping? Did you tighten it by adjusting the X-motor position?by dc42 - Ormerod
Re: heat bed mounting linear bearing - 10 years ago
Chris, I agree with you that the holes are too close to the corners, My MDF plate has partly delaminated between one of the holes and the corner.by dc42 - Ormerod
Strange behaviours - 10 years ago
I've seen some strange behaviour from my Ormerod on several occasions. The problems started after I created and started using a setbed.g file, although they may be unrelated to that because I didn't do very much before that. The issues I see are: 1. Sometimes, when homing the Y axis when the current Y position is already zero, it doesn't drive the carriage to the endstop. Instead, it tries to drby dc42 - Ormerod
Re: x axis carriage 9mm bearing not free - 10 years ago
I've done my bearing up tight - I wanted to make sure it wouldn't slip, as I had it right at the end of the slot - and the bearing rotates freely. I did make sure to put the washer the right way round (the side that bulges in the middle towards the bearing), and I also added a shakeproof washer between the plain washer and the printed part, to make sure it didn't slip against the plastic. But I'vby dc42 - Ormerod
Re: X axis sensor - G31 returns zero - 10 years ago
I thnk that makes three of us - trevor51 has just reported what sounds like the same problem. Ian, I think you need to either supply faster SD cards, or change the firmware to allow the SD card more startup time.by dc42 - Ormerod
Re: pronterface connection problem - 10 years ago
Looks like you have the same problem I had, which is that config.g is not running at startup. Workaround: press the Reset button on the Duet before trying to connect Pronterface. Fix: ditch the SD card that came with the kit and substitute a decent one (I used a Maplin own-brand 4Gb class 10 card).by dc42 - Ormerod
Re: X axis sensor - G31 returns zero - 10 years ago
Sounds like your config.g file may not be running at startup. I had the same problem. If I pressed the Reset button on the Duet, config.g did get run. I fixed the problem by ditching the SD card that came with the kit and substituting a Maplin 4Gb Class 10 SD card. However, without config.g running, Pronterface didn't regard the printer as online and so couldn't connect (the precompiled Windows vby dc42 - Ormerod
Re: X axis sensor - G31 returns zero - 10 years ago
Is the Z sensor turned on? This is normally done by the M558 P1 command in config.g.by dc42 - Ormerod
Re: Improving the proximity sensor - 10 years ago
Success! I changed those resistors, and the sensor is much less sensitive to ambient light. I even reinstated the 50W halogen bulb in the ceiling above the Ormerod, and it only increases the reading by about 15. The highest reading I get is now about 770 at 0mm and it drops to 448 at 1mm. So it's just about clear of the saturation region. I'll calibrate at 1mm or just a little higher. I had to aby dc42 - Ormerod
Improving the proximity sensor - SUCCESS! - 10 years ago
I'm finding that my proximity sensor is VERY sensitive to ambient light. I already mentioned in another post that when I had a 50W halogen bulb in the ceiling above, I couldn't make it work at all. Now I'm finding that I can't set up parameters that will reliably do the z-homing, because even the sunlight coming through the window is giving quite high readings. What I really want to do is modulaby dc42 - Ormerod
Re: re-designed z-axis mount - 10 years ago
Out of curiosity, what is the change to the z-nut trap? I'm using the new x-rib and x-plate with the old trap adjusted to fit.by dc42 - Ormerod
Re: Fan backwash causes warping? - 10 years ago
I haven't done any prints yet, but there is a huge amount of backwash from the fan on my Omerod, so much so that I thought I must have connected it the wrong way round. But I checked and it is rotating the right way to blow air through the heatsink. So I can quite believe that backwash from the fan is cooling the print too much.by dc42 - Ormerod
Re: x axis carriage 9mm bearing not free - 10 years ago
I agree, a 10mm bearing would have been better - I wouldn't have had to elongate the slot and the nut trap as much.by dc42 - Ormerod
Re: Problem building Duet firmware - 10 years ago
Hi tru168, Thanks, however that doesn't address the problem. I already have the Ethernet and SD libraries. The SD header file you linked to on github looks the same as the one I already have, and has the same references to sam.h and undefined types U8, S8 etc. The Ethernet library you linked to still doesn't have the file Ethernet_sam.h. I found there is a file called sam.h in the Arduino core,by dc42 - Ormerod
Re: Fan assembly fouls on foldback clips - 10 years ago
Ian, thanks for your feedback. I've ordered some 250x250x1.5mm alu sheet from eBay, and I'll visit my local glazier tomorrow. In the meantime I'll commission my printer by taping the print surface down as you suggest.by dc42 - Ormerod
Re: Problem building Duet firmware - 10 years ago
Hi Treth, I'm not trying to update my firmware to latest (I've already done that), I'm interested in modifying it so that I can solve the problem that I (and others) have of the IR sensor being too sensitive to ambient lighting conditions.by dc42 - Ormerod
Re: Repositioning the Z axis on the X axis bed. - 10 years ago
I agree, moving the Z axis and setting it up at a right angle is a pain. However, another benefit for me of moving it was that the print head range is now exactly from one end of the glass plate to the other.by dc42 - Ormerod
Re: Fan assembly fouls on foldback clips - 10 years ago
I've now managed to stop the print head sagging. The main problem was that the nut trap in the X runner wasn't flat, so when the bearing screw was tightened, the screw tended to move towards the outside of the runner. In the end I had to use a 3mm drill to elongate the slot, and a 2.5mm drill and knife to rework the nut trap. With the screw up against the end of the newly-elongated slot, and afteby dc42 - Ormerod
Re: Fan assembly fouls on foldback clips - 10 years ago
Thanks, Treth! Either I missed the bit about the slot, or it wasn't in the documentation a week ago when I assembled the runner. I'll take it apart and elongate the slot if necessary.by dc42 - Ormerod
Re: Fan assembly fouls on foldback clips - 10 years ago
Further to my earlier message: - When I said "X idler bearing" in my previous post, I should have said "X runner bearing". - Looking at it closely, I can see that only the very top of the runner bearing makes contact with the X-plate, confirming my suspicion that the main problem is that the runner bearing is mounted too far away from the X-plate. - If I insert a 1mm thick steel rule between tby dc42 - Ormerod