Hey Chris, If you got the dxf's or can point me at them I can probably do this. Benby plexer - Job Shop: I need stuff made!
The board runs 16 microsteps and you can't change it. Bby plexer - Reprappers
You need some female dupont connectors and some 4 way housings along with a dupont crimp tool. Bby plexer - Reprappers
I also see you mentioned issues with the igus bushings not sliding very well, I never liked the fiddly nature of those so I mashed up my own x axis ends to include linear bearings. Benby plexer - Reprappers
Good stuff A few comments, never tighten those u style clamps too much they just need to be nipped up tight enough to hold the rod in place no more. I use aluminium expanded couplers on the Z axis on my RepRapPro printed mendel they have enough give to avoid introducing issues in the z axis and they are smooth. I moved to a z max stop and run the printer using mattercontrol with auto bed leveby plexer - Reprappers
Very nice build, any video? Bby plexer - Reprappers
Ahh ok I see I had checked out that link earlier and didn't fully realise. Thanks for the heads up I printed out a set of tantilus parts and laser cut a case around 2 years ago and have never built it but with your updated corners and sliders I am going to do it Benby plexer - Tantillus
What is the actual carriage you are using there? is it on thingiverse? Thanks Benby plexer - Tantillus
Colour the belt teeth then you have a colour contrast? Benby plexer - Let's design something! (I've got an idea ...)
Unless you've broken the atmega chip on your melzi which is doesn't sound like you have as that's what they are referring to when talking about the boot loader then it's quite straightforward to upload a new firmware to the board with the correct steps value for your z axis. Benby plexer - Reprappers
I backed this on kickstarter and can say I am absolutely thrilled with how well it works, first layer sticks extremely well I use 40 degrees on my heat bed and I have no concerns over parts coming loose. I only print with PLA so can't comment on the ABS side of things. Benby plexer - Crowdfunding Projects Announcements
Some more information about your printer would also help, what is it? where are your endstops located? do you home it before probing? Benby plexer - Reprappers
I've used material like this under my bed.by plexer - Reprappers
If you are using a lcd add on so you can select the files to print I don't see a problem but I would disconnect the usb first and then start the print from the sd card. Benby plexer - Reprappers
You do not need to connect power to your arduino board it will be powered from the ramps or if that's disconnected from the 5v of the usb port. Benby plexer - Reprappers
this one any good? Benby plexer - Reprappers
Why would you want to use Mach3 with an omerod board they are designed to be used and controlled with a 3d printing toolchain which is all free anyway. Benby plexer - General
The bottom of my heatbed is insulated with layers of this and my thermistor is tape to the side of the glass with aluminium tape, the glass is also fixed to the pcb and the mdf sub plate with aluminium tape. I see no need to remove the glass to clean it I spray it with hairspray. Benby plexer - Reprappers
You don't normally need to extend these wires for a normal 3d printer the heat protection is required at the hot end for a few inches but after that chop them off and use regular wire, mines hooked up with multiple strands from a ribbon cable. Benby plexer - Reprappers
So but I don't know what your problem is. I have built 3 RepRapPro Mendels, 2 were from complete kits bought from them and the 3rd was made using parts printed on the other 2. I've printed all sorts on them including more parts and other things I've designed and downloaded from thingiverse etc... They've always been helpful and responsive to my queries the trouble is there are so many people tby plexer - Reprappers
Please provide details for the electronics you are using, stepper drivers and steppers. Benby plexer - Reprappers
So you have 2 Z steppers? are they wired in series or parallel to the driver and what vref is the driver set for? Benby plexer - General Mendel Topics
Just remember to never connect or disconnect motors whilst it is powered. Benby plexer - RAMPS Electronics
She also homes on the x and y axis just need to find some springs for the z axis lead nuts. Oh and here's a tip for those of you using micro switches with m2.5 holes in the just take a 3.2mm drill to them and use m3 hardware to mount them, much easier Benby plexer - General Mendel Topics
Steppers arrived Friday so got the belts installed and wired up today. Benby plexer - General Mendel Topics
QuoteDo not worry if this fails, I will try another funding format only trying to raise about $25,000 to cover expenses, I also doubt that will succeed but I will try it anyway. I am not really that bothered what happens as I have many other projects I am working on. This project is partly selfish as I like Linuxcnc and want to see it developed further and hope that by encouraging others to useby plexer - Crowdfunding Projects Announcements
QuoteDust "bed thermistor and if I warm that up with a lighter" so you applied 2000C to a device that is rated for 300C? I would be amazed if this thermistor is still ok. No I allowed the heat from the flame to radiate and warm up the thermistor. Benby plexer - RAMPS Electronics
I ordered these for my RRP mendel. Benby plexer - Reprappers