Can you look at my config and see that I have the content right? I copied the G30 section into the file do I still need the M557 and should the numbers match the G30 as I have them. Do I need to add the bed.g file to the sys folder? or macro folder? Is this up to date? This is what I used for my bed probingby joestefano - Duet
Update, After probing bed again the Z level seems to be correct at printing. My start code is now not working properly. It moves the heads to the purge bin then immediately moves back to the home position and heats then extrudes and begins the print. What would tell the head to move back to home from the bin?by joestefano - Duet
right after going thru the calibration process and setting G92 to Z0 I set the G31 in the config to what the M114 reads (1.85) Then I raise the heads a few mm and run G30 and the heads come down and touch the bed and Z reads 0 as it should. I then try a print file and the head prints in the air at the end of the print I home the heads and run G30 and the heads go to the level above the bed thatby joestefano - Duet
Need your help, the start code works great with EX0, When I want to use EX1 as it is now it will heat EX0 and then EX1 and purge and start the print. How do I get it to check for the selected EX and turn only that one on? If I remove T0 & T1 it will start the print before heated. Do I have to enter anything in the tfree or tpost files to get it working? Should I have already?? Setup: converteby joestefano - Duet
Have you tried Kisslicer? It works very well with multiple printers and is cheap. Thanks again for your help.by joestefano - Duet
That did it. In my defense where does it say to rename that folder "gcodes" ? Thank you very much David. Have you any experience with Simplify3D? If not what slicer do you prefer?by joestefano - Duet
Originally it was named gcodes-ormerod then I changed it to gcode because that's what you put in your last email. Now it works!!! Thank you! I am now going to try to upload from the web interface, could that have been the problem? ill get back to you. thanks againby joestefano - Duet
On my SD card I have a folder named gcode along with folders named macros, sys & wwwby joestefano - Duet
David, Do I need something in my config to point to the g code folder on the SD card? I've tried all the ways I can think of to get the files uploaded with the web Interface. I am willing to assume that I am doing something wrong, I don't see others having issues.by joestefano - Duet
Still doesn't explain why I can't see the gcode file that are already installed on the SD card.by joestefano - Duet
I just sliced and saved a .gcode file from Kisslicer to my desktop. S3D hijacked the file type. How does this happen? There is still a .stl or .gcode after the file name but the file type shows as 3D model. I've also put this out on the S3D forum. Very Strange!by joestefano - Duet
David, what happens when I try to upload a g code file is the screen (web interface) flashes and then I get the ajax time out message. I'm using Simplify3D and am very new to it, maybe I'm doing something wrong with that? The file that I save reads .gcode but shows up as 3D model in the file typeby joestefano - Duet
I have loaded some g code files on the SD card along with the files that were already loaded (G code folder). I can't see the files from the Duet or the web interface. I can't upload g code file to the web interface either. Is there a separate forum for the Web Interface?by joestefano - Duet
Orin, Did you check out the Duet board? I am just finishing up a Duo conversion. Great board!by joestefano - Firmware - Marlin
Dane, I am just finishing up a Duo conversion using a Duet board. I also changed the extruders to Bowden to lighten up the gantry. This Duet is amazing. I just preordered the new Duet WiFi board. I'm going to use it to convert my Trio.by joestefano - General Mendel Topics
Has anyone found a good glue for PLA? Super glue does not seem to work even when clamped for a time.by joestefano - Reprappers
Thanks Guys all the suggestions worked great. Now if I can figure out how to get a part into Alibre Design.by joestefano - Reprappers
Thanks for your reply. I downloaded the plugin, but when I try to open a STL file I get a the following message. Invalid file format: No solid name found, or not an ASCII STL file. Any ideas?by joestefano - Reprappers
How do I open a STL file so that I can make changes to the part? ie dimensions, hole locations ect. I have Alibre Design, Autodesk Inventor and Sketch up. None of them seem to Import STL file, they will export them.by joestefano - Reprappers
Thank you for your response, Wher can I find this "Tower Test"??by joestefano - Reprappers
Have you tried white ABS? That works great for me. or try some of your extruder purging strings.by joestefano - Reprappers
What extruder temp. are you folks using when printing ABS on a 120C glass heated bed? 1st layer different from the rest? I assume no PLA raft.by joestefano - Reprappers
Hey Guys, I have a RapMan 3.2 double head. I am experimenting with a MK2A attached to the factory acrylic bed with standoffs in the 4 corners. On top of the MK2A I have a 1/4" Fire rated piece of glass held down with small aluminum brackets secured to the acrylic bed in 4 places. Now here is the problem, almost immediately upon turning on the power the bed begins to rise as much as .040 at 130 C.by joestefano - Reprappers
Hey Guys, I have a RapMan 3.2 double head. I am experimenting with a MK2A attached to the factory acrylic bed with standoffs in the 4 corners. On top of the MK2A I have a 1/4" Fire rated piece of glass held down with small aluminum brackets secured to the acrylic bed in 4 places. Now here is the problem, almost immediately upon turning on the power the bed begins to rise as much as .040 at 130 C.by joestefano - Reprappers
What Temp would you recomend for ABS part with a PLA raft? How are you guys regulating the temp? I have a MK2A, Rapman 3.2by joestefano - Reprappers
I purchased a MK2A Heated Bed for my RapMan 3.2. What should I use for a power supply? I am going to mount it under a pane of 3mm glass.by joestefano - Reprappers