Welcome! Log In Create A New Profile

RAMPS Electronics

Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS.

Page 67 of 72 Pages:

65 666768 69

Forum List New Topic RSS

	Views	Posts	Last Post
1 test big print by michel pet	1,184	4	03/18/2012 11:31PM Last Post by michel pet
Nothin on the heated bed by mydogjustice	889	3	03/18/2012 08:00PM Last Post by mydogjustice
SDRAMPS hints by Dale Dunn	3,119	20	03/14/2012 03:31PM Last Post by aplavins
Trying to compile and install firmware for RAMPS 1.3 by ddon	1,639	8	03/13/2012 10:55AM Last Post by Chompalot
Problem getting ramps 1.4 to work by HereIgoAgain	1,244	4	03/13/2012 05:55AM Last Post by dissidence
ramps touchscreen by shinjinian	1,471	2	03/11/2012 09:35AM Last Post by Justblair
print failed mid way through by ambiguousphoton	969	2	03/08/2012 05:31PM Last Post by aplavins
Extruder Heater: Reaches Temp, then termistor not readable by Augustum	1,455	4	03/08/2012 05:21PM Last Post by aplavins
Adding cooling fan questions by Kassie	9,134	10	03/08/2012 05:05PM Last Post by aplavins
Filament is sticking to Hot End Nozzle but not to the bed. What I'm doing wrong? by Kaage	4,211	6	03/08/2012 05:54AM Last Post by Kaage
How hard is the smd soldering (DIY kit)? by JoeDaStudd	2,684	8	03/05/2012 07:26PM Last Post by George
RAMPS1.4 gerber files by bcndynamics	1,730	3	03/05/2012 02:39PM Last Post by bcndynamics
Weird pulsing Issue with RAMPS 1.4 - pots on motor drivers are turned all of the way down and heat sink stays cool by voodoomagicman	2,196	10	02/28/2012 03:48AM Last Post by nophead
[Solved] Change direction in Marlin by oddovalspin	1,823	3	02/28/2012 03:12AM Last Post by oddovalspin
Hot end is not getting hot enough by Kaage	1,075	3	02/24/2012 04:30AM Last Post by Kaage
Problems with 16x microstepping by martinprice2004	1,498	4	02/23/2012 04:35PM Last Post by nophead
short question - pololu1182 by Bajn	963	1	02/23/2012 06:20AM Last Post by Bajn
V1.4 PS-ON by rwskinner	1,310	3	02/22/2012 07:43AM Last Post by Andrew Smith
How to disable endstops by johnoly99	1,459	2	02/21/2012 10:18PM Last Post by johnoly99
RAMPS 1.2 problem by Chaosak	1,213	5	02/21/2012 08:41AM Last Post by Chaosak
two steppers on one axis by geronimo	7,633	7	02/20/2012 02:24PM Last Post by DaveX
PSU shuts down trying to power heated bed by unicoder	3,330	8	02/16/2012 05:19PM Last Post by Traumflug
Noise on opto-end line by rGlory	837	1	02/13/2012 11:47AM Last Post by rGlory
A problem with PC power supply by tsbmthai01	1,162	4	02/12/2012 06:05PM Last Post by aplavins
Why the thermistor needs a power transistor? by oniric	1,098	3	02/10/2012 04:23AM Last Post by oniric
Can I try RAMPS on a breadboard? by oniric	1,888	7	02/09/2012 07:53AM Last Post by oniric
Extruder missing steeps mid-printing by pikelo	1,044	6	02/08/2012 11:44PM Last Post by aplavins
Ramps 1.4 motors unresponsive by bronzies	1,673	6	02/08/2012 11:11PM Last Post by aplavins
Thoughts on wiring before I go to far down the wrong road by mydogjustice	1,010	2	02/08/2012 10:45PM Last Post by aplavins
Safe to replace 1N4004 with SY 320/8? by anwe79	2,359	3	01/26/2012 06:15AM Last Post by anwe79

Page 67 of 72 Pages:

65 666768 69