Subject		Views	Posts	Last Post
	First layer failing! by pikelo	1,152	5	08/11/2012 04:48PM Last Post by cokezero91
	Infill Problems? by cokezero91	2,313	5	08/11/2012 04:43PM Last Post by cokezero91
	leaking tip by badhank	839	4	08/10/2012 02:30PM Last Post by badhank
	Change the space in between each pass of plastic? by cameronm	921	4	08/08/2012 06:34PM Last Post by cameronm
	bad surface quality - getting tired of gambling... by Irgendwer_Aus_Irgendwo	1,501	4	08/07/2012 08:43AM Last Post by Weedz
	Z-Axis getting higher and higher during prints? by sam0737	1,260	12	08/04/2012 05:05PM Last Post by sam0737
	dribble, drizzling j-head problem by hitman1131	1,104	4	08/03/2012 10:42PM Last Post by Gulf
	Pronterface not printing on Prusa in same location by burkferden	1,081	2	08/02/2012 03:56PM Last Post by MotoBarsteward
	Filament slipping? by sam0737	1,550	7	08/01/2012 03:21AM Last Post by sam0737
	PVA printing paramters by Rilakkuma	681	1	07/31/2012 08:54AM Last Post by Rilakkuma
	STL Repair Fail by RegionX	1,051	4	07/30/2012 11:08PM Last Post by NewPerfection
	a few issues left by cwahlin	907	3	07/30/2012 03:16AM Last Post by cwahlin
	Strange Y-shifting by ifrisbie	768	1	07/29/2012 07:10PM Last Post by ifrisbie
	Getting dimensions right: is that perimeter width, or flow rate, or what? by sam0737	2,846	6	07/28/2012 04:06PM Last Post by sam0737
	First time print help by ifrisbie	1,553	24	07/24/2012 07:52PM Last Post by Weedz
	Small Layers Not Adhering by gtg252b	1,013	13	07/23/2012 09:44PM Last Post by gtg252b
	J-Head Jam (premature melting) by MaFraL	3,029	12	07/22/2012 07:20PM Last Post by MaFraL
	An Attempt to print a Small Cylinder by flurin	2,593	9	07/17/2012 09:31AM Last Post by flurin
	Printing prusa bar clamp by 3D2B	1,297	8	07/15/2012 04:35PM Last Post by 3D2B
	Printrbot with Gen7+Slic3r: Print Quality issues by peter6960	3,012	4	07/14/2012 02:57PM Last Post by peter6960
	PrintBed leveling - prusa by ifrisbie	2,005	26	07/12/2012 10:00AM Last Post by ifrisbie
	Can anyone spot the slight problem with this print? by MotoBarsteward	937	3	07/11/2012 08:03PM Last Post by MaFraL
	Using dilute PVA glue to stop curling by MotoBarsteward	3,366	10	07/11/2012 02:40AM Last Post by MotoBarsteward
	Can excess filament cause curl? by nb99	974	1	07/06/2012 09:23PM Last Post by nb99
	print area out of bounds by paddy10tellys	1,473	5	07/05/2012 09:43PM Last Post by dustynus
	Hole, inside and outside dimensions wrong by MotoBarsteward	3,050	11	07/04/2012 06:49PM Last Post by MotoBarsteward
	Weird curling with PLA on heated bed of glass by Mazaw	8,232	20	07/03/2012 01:48PM Last Post by idiot_secant
	Nozzle touching the object after going up 5mm by scanboy	1,242	5	07/03/2012 12:56AM Last Post by aplavins
	Stripes/Layers by cunningham	1,022	3	07/03/2012 12:51AM Last Post by aplavins
	Single Wall cube test by Etherflash	1,415	5	07/03/2012 12:45AM Last Post by aplavins