Welcome! Log In Create A New Profile

Tantillus

http://www.reprap.org/wiki/Tantillus

Page 6 of 12 Pages:

4 567 8

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	1/4 inch acrylic by wingnut	1,102	8	09/16/2013 01:56AM Last Post by Helmi
	Light rust on smooth rods by cameronm	1,954	7	09/13/2013 08:41PM Last Post by Sublime
	Endstop not responding properly by Nick101	1,404	3	09/09/2013 03:14PM Last Post by Nick101
	Is it worth converting my Printrbot Jr. into a Tantillus? by cjdj3	1,666	3	09/06/2013 01:51PM Last Post by Guizmo
	"The Keep it Dry" by willworkforplastic	3,062	12	09/05/2013 11:48AM Last Post by SkyArcher
	Motor issues by Nick101	944	7	09/05/2013 02:07AM Last Post by gonniP
	Printing Taulman 618 Nylon on Tantillus by willworkforplastic	2,118	3	09/02/2013 02:46AM Last Post by willworkforplastic
	Hotend Resistor by neptix	1,445	7	08/30/2013 04:15PM Last Post by Nyarlathotep
	Filament feed issues by maik	2,499	5	08/29/2013 07:46PM Last Post by lajos
	Tantillus Metric with 5mm Acylic by zungmann	1,195	4	08/24/2013 11:16PM Last Post by zungmann
	LCD/Powering question by maik	1,228	10	08/23/2013 02:07PM Last Post by Sublime
	Retraction(?) blobbing by maik	1,741	6	08/21/2013 07:09PM Last Post by Sublime
	Clarification of parts required (and sourcing) (Pages: 1 2) by Yonderboy	4,368	42	08/15/2013 02:27AM Last Post by Sublime
	Squaring and Tensioning woes by Nick101	801	6	08/14/2013 11:48AM Last Post by Nick101
	SkyArcher's Tantillus by SkyArcher	1,367	12	08/10/2013 03:52PM Last Post by SkyArcher
	larger one ? by imprime3d	726	3	08/09/2013 07:32AM Last Post by imprime3d
	Bed too low by maik	808	5	08/02/2013 04:03PM Last Post by Sublime
	updated marlin firmware by lajos	3,097	16	08/02/2013 01:56PM Last Post by SkyArcher
	Yet another new variation on Tantillus. by Sublime	1,203	2	08/02/2013 03:17AM Last Post by cns1
	too many retracts when slicing hollow object by lajos	1,147	5	07/29/2013 03:33PM Last Post by lajos
	LM8UU + LM8SUU vs 2x LM8UU ? by maik	2,512	5	07/27/2013 02:05PM Last Post by Sublime
	X-y drive rods by SkyArcher	796	2	07/25/2013 11:34PM Last Post by Sublime
	Hotend Options by beekeg	1,630	12	07/25/2013 01:20PM Last Post by Arc_Tesla
	Intricate print with support by Sublime	3,339	9	07/21/2013 07:59AM Last Post by Eric Young
	Z Lift Stl by plexer	852	5	07/19/2013 05:50PM Last Post by plexer
	Sharing some prints by Nico3ck	1,130	6	07/14/2013 06:35AM Last Post by Nico3ck
	Tantillus with belts by Sublime	1,527	3	07/13/2013 01:57AM Last Post by Sublime
	User settings by Sublime	1,259	12	07/12/2013 11:42PM Last Post by Eric Young
	Where can i find a 20 position encoder by dearnir	966	2	07/11/2013 03:53PM Last Post by flemming
	New assembly question by robster34	902	7	07/10/2013 12:17PM Last Post by Sublime

Page 6 of 12 Pages:

4 567 8