Welcome! Log In Create A New Profile

Ormerod

RepRapPro's Ormerod http://reprap.org/wiki/Ormerod

Page 3 of 83 Pages:

1 234 5

Forum List New Topic RSS

	Views	Posts	Last Post
5 Years ago - It was the best of times, it was the.. by ormerod168	2,650	10	02/12/2019 07:54AM Last Post by Ormerod187
Trying out 1.23 firmware by PvtTUX	1,613	3	02/11/2019 01:30PM Last Post by PvtTUX
Adding a limit switch to x axis by Sardi	1,738	3	02/09/2019 05:51AM Last Post by Sardi
Banding on walls? by veryevil	1,890	9	01/25/2019 05:42AM Last Post by cheeseandham
Back again after 3 years by spiff	1,842	22	01/12/2019 02:20PM Last Post by spiff
Building an Ormerod 2 from scratch by sinnedwrong	3,587	30	01/09/2019 04:18AM Last Post by sinnedwrong
Ormerod 2 web interface buttons lost by DaveGray65	1,296	3	01/06/2019 05:38AM Last Post by DaveGray65
More mesh levelling issues by cheeseandham	3,802	22	01/01/2019 03:49PM Last Post by cheeseandham
Printing ABS by chriscain	1,695	8	12/14/2018 04:48AM Last Post by Karoo Klong
E3D V6 - Should I change the stock print head? by Karoo Klong	1,199	6	12/14/2018 04:29AM Last Post by Karoo Klong
Source for STL for part 741 Quick-set hot end fan spacer? by gwild	1,676	18	12/12/2018 02:41AM Last Post by Karoo Klong
Another alternative Hot-end cooling duct. by Form232-tek	4,809	28	12/12/2018 02:36AM Last Post by Karoo Klong
where can I get the ormerod.ini of DC42 for slic3r? by sevenljy	1,714	12	12/12/2018 02:34AM Last Post by Karoo Klong
Second printer by jamesf	1,661	21	12/07/2018 07:16AM Last Post by trevmas
Replaced the cooling fan with a noctua one. I'm sane again! by improprietary	1,848	10	12/06/2018 07:07PM Last Post by Karoo Klong
Layer cooling with an Ormerod 2 by cheeseandham	1,261	19	12/06/2018 03:43PM Last Post by Karoo Klong
HELP -----> Need slic3r config - Start/End G-Code by ormerod2_user	1,568	3	12/06/2018 03:11PM Last Post by Karoo Klong
Printing Files on my RepRap Ormerod 2 by cjdudley	978	4	12/06/2018 08:14AM Last Post by Karoo Klong
3DBenchy on Ormerod by WesBrooks	1,155	2	12/06/2018 07:51AM Last Post by Karoo Klong
Spring loaded extruder is not working (for me) (Pages: 1 2) by Treito	4,393	47	12/06/2018 05:06AM Last Post by Karoo Klong
New Ormerod, some issues by ein	1,703	21	12/05/2018 05:59AM Last Post by Karoo Klong
Fix your clips! by WesBrooks	930	4	12/05/2018 05:00AM Last Post by Karoo Klong
The Alumarod needs manual mesh bed leveling (Pages: 1 2) by Karoo Klong	3,448	60	12/03/2018 05:02PM Last Post by Karoo Klong
Ormerod Bigfoot mod! by ormerod168	3,139	20	12/03/2018 06:12AM Last Post by Karoo Klong
Ormerod 2 Y Axis End Plate Snapped! by veryevil	946	8	11/30/2018 12:45PM Last Post by veryevil
(Guide) Swapping from bed.g to 4 point mesh with repeat probes. by WesBrooks	1,266	5	11/23/2018 10:59AM Last Post by dc42
Rapidly becoming a home for old Ormerods! by WesBrooks	920	6	11/23/2018 07:38AM Last Post by cheeseandham
Wifi/ethernet conflict by bartdietrich	1,334	11	11/21/2018 03:48PM Last Post by cheeseandham
Bed leveling issue - how is this even possible? (Pages: 1 2) by Sardi	8,006	38	11/15/2018 06:04PM Last Post by Karoo Klong
Any Ormerod oners from Cape Town? (Pages: 1 2) by Karoo Klong	2,690	31	11/15/2018 04:44AM Last Post by Karoo Klong

Page 3 of 83 Pages:

1 234 5

Ormerod

Spring loaded extruder is not working (for me) (Pages: 1 2)

The Alumarod needs manual mesh bed leveling (Pages: 1 2)

Bed leveling issue - how is this even possible? (Pages: 1 2)

Any Ormerod oners from Cape Town? (Pages: 1 2)