Welcome! Log In Create A New Profile

Advanced

Problemi e qualità di stampa

Avete appena stampato un cubo ed è venuto fuori un prisma? Volete un parere sulla qualità della stampa? Chiedete consiglio qui.
Se siete agli inizi non chiedete qui ma nella sezione dedicata ai principianti. 
Subject Views Posts Last Post
Sticky

►►►► LINEE GUIDA E REGOLE PER UN USO CORRETTO DEL FORUM ◄◄◄◄ Da leggere! Segnalate ai moderatori le discussioni da chiudere - LE REGOLE VANNO LETTE E APPLICATE!

by Gordie
2,078 1 03/09/2014 08:22AM
Last Post by Gordie

Stampa specchiata su CoreXY Attachments

by alil2096
44 3 10/15/2018 03:17AM
Last Post by alil2096

Kossel problema primo strato Attachments

by Renthar
39 1 10/08/2018 06:52PM
Last Post by Renthar

Anycubic Photon

by paolopa
119 2 10/06/2018 07:44AM
Last Post by Mr Yod

Blob solo su parti circolari Attachments

by whitedavil
77 2 10/01/2018 08:14AM
Last Post by bilanciamist

Problemi con pezzi di grandi dimensioni

by Lothar
125 14 09/28/2018 06:42AM
Last Post by Lothar

problema primo layer Attachments

by snowmax
101 3 09/25/2018 06:10AM
Last Post by Lothar

Cubo 20mm layer successivi più piccoli

by callievi
125 4 09/21/2018 06:32AM
Last Post by onekk

Ad un tratto....problemi risclad. e temp. fuori controllo

by tronicman
67 4 09/20/2018 06:09PM
Last Post by onekk

strano errore Attachments

by mga
95 4 09/10/2018 12:11PM
Last Post by alil2096

Stampa ondulata Attachments

by turambar
133 4 09/05/2018 01:43PM
Last Post by onekk

layer slittati Attachments

by f.distefano
80 2 08/19/2018 01:48PM
Last Post by bilanciamist

Linee dritte stampare ad arco su CoreXY

by Skytter
120 4 08/18/2018 05:07PM
Last Post by Skytter

Problema incrementi asse z

by lucapicchio1
93 6 08/13/2018 11:02AM
Last Post by onekk

Problemi con la stampa da SD CARD

by kirk000000000
86 2 08/04/2018 02:13PM
Last Post by giuseppegrassano

Asse Y non funzionante

by Gianmarco
79 5 07/30/2018 06:39AM
Last Post by onekk

Pezzo uscito il doppio più alto

by lorenzo_03
147 13 07/26/2018 01:32PM
Last Post by bilanciamist

Gli Assi si sfasano mentre stampa Attachments

by cristianma92
136 7 07/12/2018 04:04AM
Last Post by alil2096

PROBLEMA FILO INTRECCIATO NELLA BOBINA

by ADRIANO3D
118 4 07/11/2018 07:07AM
Last Post by Gordie

Estensione "magra E grumosa"

by mattia952
174 14 06/27/2018 06:16PM
Last Post by mattia952

Problemi Layer Cura 3.3.1 Attachments

by laudix
195 9 06/12/2018 11:18AM
Last Post by laudix

Pause durante la stampa (MarlinKimbra)

by vischio96
279 22 06/09/2018 02:21PM
Last Post by vischio96

Problemi temperatura piatto difficile superare i 60 gradi

by giuseppei75
102 6 06/05/2018 08:59AM
Last Post by giuseppei75

slittamento layer   (Pages: 1 2)

by giuseppe.it
422 35 06/01/2018 11:46AM
Last Post by giuseppei75

Configuration_overall come implementarlo se non cè in marlin?

by giuseppe.it
161 10 06/01/2018 11:43AM
Last Post by giuseppei75

Problema di stampa Attachments

by Pietrogramma
136 6 06/01/2018 10:53AM
Last Post by Pietrogramma

Problemi stampa ABS Attachments   (Pages: 1 2 3)

by Balza
7,588 68 05/31/2018 01:14PM
Last Post by Felixmau

Problema perdita passi asse Y- molto strano

by Bumbex
204 8 05/14/2018 11:49AM
Last Post by giuseppe.it

temperatura fuori controllo

by nanigago
185 6 05/13/2018 01:53PM
Last Post by nanigago

stampa schiacciata

by nanigago
246 26 05/01/2018 09:03AM
Last Post by onekk

oddio.. che ho fatto!?eye popping smileyangry smiley Attachments

by ZIOLele
332 5 04/30/2018 06:18AM
Last Post by ZIOLele