Welcome! Log In Create A New Profile

Advanced

Prusa i3 and variants

http://reprap.org/wiki/Prusa_i3 
Page 46 of 60    Pages: FirstPrevious4445464748NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Build an enclosure

by built350camaro 		434 4 12/08/2015 02:59PM
Last Post by AudaciousTuddle

Prusa i3 Hephestos - Fans and Extruder conectors name/model

by Nandox7 		1,170 1 12/08/2015 10:56AM
Last Post by Nandox7

Probably an easy fix but something i've overlooked...

by muntahunta 		354 5 12/06/2015 07:06PM
Last Post by muntahunta

Autoleveling

by valdowb 		392 1 12/06/2015 03:04AM
Last Post by valdowb

Power supply Question

by watlooazn 		309 2 12/05/2015 08:08PM
Last Post by AudaciousTuddle

P3 steel and I3 rework rp.

by Dark Alchemist 		2,712 21 12/05/2015 09:23AM
Last Post by Justsomeguy1983

2004 LCD SD Card Problem Wont Print.

by tpb0420 		514 3 12/03/2015 10:32PM
Last Post by tpb0420

Heated Bed continuously heats during prints

by bruceleroy 		342 2 12/02/2015 04:46AM
Last Post by o_lampe

Problem Prusa i3 Dual Extruder Replikeo Attachments

by ultra9 		952 4 12/01/2015 07:56AM
Last Post by RRuser

Anyone successfully upgrade the X-axis to v-slot?

by hejman08 		582 3 11/30/2015 04:21PM
Last Post by animoose

Prusa I3 - Kit purchase and upgrade?   (Pages: 1 2 3)

by noogie 		3,577 76 11/30/2015 04:04PM
Last Post by msaeger

PLA print flexes/lifts up when printing - what causes it?

by Diabl0 		396 3 11/30/2015 02:37PM
Last Post by Diabl0

Melzi upgrade board ATMEGA2560 brand Xinray

by garaguido 		415 1 11/30/2015 08:39AM
Last Post by garaguido

Prusa i3 X carriage orientation - Do I have to disassemble the entire axis ???

by Roy_Peer 		352 2 11/29/2015 03:05PM
Last Post by Roy_Peer

Prusa i3 - Filament jams, reverses during some prints

by Diabl0 		509 5 11/29/2015 05:36AM
Last Post by Diabl0

Saving a print half way through...

by Flyer 		344 2 11/29/2015 12:54AM
Last Post by RRuser

Exploding A4988 Motor Drivers on Sunhokey Prusa i3

by misterhamin 		984 7 11/28/2015 07:01PM
Last Post by misterhamin

Print cooling fan

by msaeger 		455 2 11/27/2015 02:43PM
Last Post by karimm

Hesine Prusa i3 - Missing instructions and/or software - could someone post it?

by Diabl0 		739 5 11/26/2015 06:44PM
Last Post by Diabl0

Potential heater bed Problems

by Awesome__Guy 		332 2 11/26/2015 04:33PM
Last Post by imqqmi

Does room temperature affect PLA printing?

by Bratan 		953 5 11/26/2015 09:36AM
Last Post by Nicken83

Can't connect to Arduino anymore??confused smiley

by Ecky 		17,096 12 11/26/2015 08:57AM
Last Post by AudaciousTuddle

Layer Adhesion Problems

by soccerox817 		854 4 11/26/2015 08:31AM
Last Post by Qdeathstar

direct drive extruder mounting idea, any good?

by jimmyclarke 		2,579 4 11/25/2015 04:11AM
Last Post by jimmyclarke

Prusa i3 endstop wiring mistake Attachments

by igel 		439 2 11/24/2015 11:54PM
Last Post by igel

Folger Tech 2020 Prusa i3 x-axis very loud; x motor very hot

by mccannk 		1,673 9 11/24/2015 11:53PM
Last Post by igel

Wilson II Questions

by phibez3000 		796 6 11/24/2015 11:24AM
Last Post by awesomed1

licensing on Prusa i3 variants

by Antscran 		408 2 11/23/2015 12:49PM
Last Post by J-Max

Feeder vom zweiten Extruder macht nix

by flobo79 		414 6 11/23/2015 09:10AM
Last Post by imqqmi

Can someone identify this LCD controller for me? P802M Attachments

by gwc2795 		788 2 11/23/2015 08:30AM
Last Post by gwc2795
Page 46 of 60    Pages: FirstPrevious4445464748NextLast