Hi I'm using marlin 1.19+bugfix and trying to set the steps/mm on my axis. I have succeeded in setting the X.Y axis correctly but I can't define the movement of the Z axis. When I make 10mm move the axis only moves 5mm. The command that I'm playing with in marlin is #define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 16000, 1000 }. I'm using a 0.9deg motors, M5 thread rods and DRV8825 motor driversby tolisn - Firmware - Marlin
Thank you, can I do the same after auto bed leveling ?by tolisn - Firmware - Marlin
After doing a homing procedure is the anyway to send the nozzle to park in the center of the printbed ? I used pronterface to do this but is there any way to configure Marlin to do this without pronterface ?by tolisn - Firmware - Marlin
Yes, that is how it is. Where do I make changes in marlin2 to center the print area and to set the auto bed leveling positions?by tolisn - Firmware - Marlin
Sorry for the misunderstanding, what I meant to say is during the home stage the extruder assembly moves to the left (that is where the endstop is) and the heat bed moves to the back (that is where the endstop is).by tolisn - Firmware - Marlin
When I press HOME, the bed moves to the left and to the back. Is this normal?by tolisn - Firmware - Marlin
Hi I'm new to this 3D printing hobby so be easy.\ I have generic reprap printer with the X,Y endstop located on the LEFT and BACK of the printer so I asume that the 0/0 position of the printer is located on the Left/Back of the print bed. Now all the examples that I have found use the 0/0 position as the Front/Left of the print bed and that has gotten me confused. I also have a bltouch probe locaby tolisn - Firmware - Marlin
Thanks for your quick reply Where is this setting located in the marlin files ? Do I also have to change the microstepping? currently my drivers are set to 1/32 stepping ?by tolisn - Firmware - mainstream and related support
Hi Does Marlin firmware support the use for 0.9deg steppers ? What parameters must be changed to install these ?by tolisn - Firmware - mainstream and related support
I have taken the time to correctly align the threaded rods and the whole bed assembly. The four end corners lie flat on the bench Without the motor connected, the bed moves by itself when I tilt the whole assembly to the side. After I connect the motor it seems to me that it is hard to move.by tolisn - Prusa i3 and variants
Hi I'm building my first reprap prusa I3 printer (achatz edition). During the assembly of the y carriage parts I noiticed that the movement of the bed is a little hard by hand. Although it is smooth if I move it by hand it seems to me that it is a little hard, and I'm wondering if the motor will be able to move it ? Everything is connected including the belt and the stepper motor. Can anyone shby tolisn - Prusa i3 and variants
The e3d v6 that I have does not require the ptfe tube. it is made for 3 millimetre filament. if I do not use the washers then the hotend will not tighten to the extruder.by tolisn - Prusa i3 and variants
Hi fellow reprapers I'm building my first reprap printer and have some problems (don't we all !!) while at it. At this time I'm finishing the extruder and hotend assembly and something looks weird. The extruder is a greg wades extruder V5 and the hotend is a E3D V6. I also have a groove mount aluminum plate used to attach the hotend to the extruder. The neck (groove end) of the hotend fits OKby tolisn - Prusa i3 and variants
Hi and thanks for the reply. So you think that the y-axis carrier is not aligned correctly and that is why the y-axis bed plane is not parallel with the x-axis smooth rods? What modifications/upgrades did you do to your printer ?by tolisn - Prusa i3 and variants
Hi there fellow reprapers. This is my first 3d printer build and I'm taking it slowly in order to get as much correctly as I can. I'm in the phase of building the frame of my prusa i3. The frame is an Achatz edition. The frame has 8mm threaded rods and I figured that I should use locknuts all around in order to prevent loose nuts in the future. Maybe this was an overkill but I used them anyway. Nby tolisn - Prusa i3 and variants
So I simply make the connection to Aux1 and I can read all the information ? Is there a known protocol that I can use to read the information or is it a dump of all the info and I have to sort it out? I want to use this to see info on a remote android tablet.by tolisn - RAMPS Electronics
Hi. Is it possible to add a bluetooth dongle to the ramps board in order to monitor the status of the printer? has anyone done this ? What I want to do is the following. Have a standalone printer (no pc connection) that uses an sd card to print the part. So far so good as this has been done and works great. While printing it would be nice to have information such as temperatures, time left,,,eby tolisn - RAMPS Electronics
So in other words it is a PANIC button and not a simple STOP-PAUSE/RESUME button.by tolisn - Controllers
Hi. I'm just starting out with building my first 3d printer. While waiting for some parts to come in I started playing with the LCD. The lcd is hooked up to a ramps1.4 board and arduino. Marlin is used for the firmware and the lcd works great. One thing that I have seen is that when I press the stop button on the lcd board it freezes the system. I don't know if it freezes the arduino or only theby tolisn - Controllers
Η ανησυχία μου είναι περισσότερο για το θέμα πυρκαγιάς και όχι για τις αναθυμίασης. Έχετε κάποια άποψη για το θέμα ?by tolisn - Greek RepRap User Group, ελληνική ομάδα χρηστών
Γιατί με PLA/teflon δεν υπάρχει πρόβλημα ενώ με το ΑΒS υπάρχει ? Μπορείς να εξηγήσεις ?by tolisn - Greek RepRap User Group, ελληνική ομάδα χρηστών
Γεια σας συνάδελφοι RepRapers Έχω αρχίσει και εγώ να ασχολούμαι με το 3D άθλημα αλλά με απασχολεί το θέμα της ασφάλειας. Πόσο ασφαλές είναι ένας εκτυπωτής 3D της κατηγορίας prusa που λειτουργεί σε ένα περιβάλλον όπως το δωμάτιο ενός σπιτιού ?by tolisn - Greek RepRap User Group, ελληνική ομάδα χρηστών
φίλε trustfm έχεις κάνει καταπληκτική δουλειά στο tutorial, έχω όμως κάποιες απορίες που μάλλον μπορείς να μου τις λύσεις. 1. Στην ρύθμιση του stepper driver έχεις συνδεμένο το αντίστοιχο μοτέρ ? 2. Γιατί η ρύθμιση πρέπει να γίνεται χωρίς τροφοδοσία ?by tolisn - Greek RepRap User Group, ελληνική ομάδα χρηστών
I have a gregs wade v5 extruder and I am thinking of installing a E3D V6 all metal hotend. Is this a good combination?by tolisn - General Mendel Topics
Hi fellow 3Ders I building my first 3D printer and decided to go with the prusa i3 single frame. I'm trying to do my homework while waiting for the frame kit to come in. Trying to select an extruder is very confusing so I'd though I should ask the pros, you guys. I'd like an extruder the will permit the easy install and removal of the filament and that does not have a lot of operation problems.by tolisn - General Mendel Topics