Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

What 2-Pin screw terminal block size does RADDS use?

by Lobotomy
366 3 04/18/2018 03:55AM
Last Post by o_lampe

Stepper motor controller which is not CNC?

by Elm999
391 9 04/16/2018 03:16AM
Last Post by o_lampe

FSP psu 150watt dead Attachments

by endruw
333 3 04/15/2018 03:07PM
Last Post by endruw

RAMBo No Stepper Response

by benkitesurfs
329 3 04/14/2018 12:20AM
Last Post by benkitesurfs

Jumper settings for Rumba board? Attachments

by Tomsand
609 3 04/05/2018 03:14AM
Last Post by o_lampe

[solved] Rumba board + relay + heated bed Attachments

by Tomsand
452 2 04/04/2018 02:05PM
Last Post by Tomsand

Are microprocessor pin current limits dependent on frequency?

by Olsla
373 2 03/28/2018 04:45AM
Last Post by VDX

MKS SBASE V1.3 change Stepper Drivers

by Tryptamine
10,261 12 03/27/2018 07:26PM
Last Post by Hedobum

32bit Marlin compatible?

by DaHai8
668 2 03/26/2018 01:56AM
Last Post by alejanson

MKS Sbase and Octoprint

by kapperi
1,054 3 03/16/2018 11:42AM
Last Post by kapperi

Extending Smart RAMPS Tips and Advice

by mohala
914 3 03/03/2018 03:11PM
Last Post by mohala

Streaming G-code to 3D printer board from micro-controller

by CharlesDesign
818 4 02/22/2018 03:06AM
Last Post by obelisk79

Hello everyone I tried everything I do not know what to do anymore I'm adding photos of settings I've set up My board is RUMBA BIQU 1. my board configuration.h [IMG] 2. configuration_avd.h [IMG] 3. pins_RUMBA.H [IMG] please help me Thank you

by amirgaziel0
444 4 02/21/2018 12:18AM
Last Post by Dust

MKS Robin and MAX31855

by zheka1980
551 1 02/17/2018 11:45PM
Last Post by zheka1980

EEPROM issues with Rumba board

by philibuster
551 4 02/13/2018 11:01AM
Last Post by philibuster

GT2560 USB-Stick Reader

by maeckes
454 2 02/12/2018 10:38PM
Last Post by Dust

Does teacup support i2c?

by lalbe
525 2 02/09/2018 05:49AM
Last Post by Traumflug

Help to modify Cramps to add 50w Spindle support Attachments

by lordrafa
523 3 02/06/2018 01:27PM
Last Post by lordrafa

troubleshooting with TFT28 V1.2 Attachments   (Pages: 1 2)

by jmn47
10,994 33 02/04/2018 09:15AM
Last Post by epoxi

MKS Robin v2.3. Connectors XS1 and XS2

by zheka1980
683 4 02/04/2018 03:25AM
Last Post by zheka1980

MKS Base v1.4 w/ external stepper driver

by S1CAR1US
2,779 6 02/02/2018 03:57PM
Last Post by S1CAR1US

MOSFET IRF1010NS Equivalent Substitute

by serandre
392 2 02/01/2018 06:36PM
Last Post by VDX

can't upload my files to arduino nano Attachments

by lalbe
1,463 3 01/30/2018 05:08AM
Last Post by lalbe

It's time for RAMPS-FD v2...   (Pages: 1 2)

by bobc
7,252 32 01/29/2018 05:35PM
Last Post by Giftyakapatch

RAMPS for BeagleBone   (Pages: 1 2)

by cdsteinkuehler
9,072 51 01/14/2018 09:33AM
Last Post by jeroen79

rambo board problems

by romon
532 3 01/04/2018 06:31PM
Last Post by romon

Help to find a driver for my 57HD0401 15SB

by lordrafa
2,287 5 01/03/2018 04:39AM
Last Post by o_lampe

MKS TFT 32 Firmware will not update

by usajet
1,951 4 01/02/2018 08:39AM
Last Post by seabassattitude

What the heck is mnm? (in relation to stepper motors.)

by Caliber Mengsk
12,908 6 12/28/2017 02:42AM
Last Post by VDX

[NEW] OVM20 Lite, a simple board for lowcost printers

by staticboards
1,947 22 12/17/2017 10:50AM
Last Post by obelisk79