Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Page 4 of 78    Pages: Previous12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Dumb question about RADDS hall sensor

by bryanbdp 		280 2 08/21/2017 03:14AM
Last Post by o_lampe

How to set up microstep on StepStick using A4988 ?

by trietdao95 		343 3 08/16/2017 08:15PM
Last Post by Dust

tronxy melzi 2 boards??

by munchit1 		596 5 08/15/2017 10:21AM
Last Post by munchit1

What's the easiest way to do this?

by Desertboy 		290 2 08/15/2017 03:58AM
Last Post by o_lampe

The probably cheapest and most modular 32bit solution.

by JustAnotherOne 		745 7 08/12/2017 03:00PM
Last Post by JustAnotherOne

Sinaptec DIY build Attachments

by Dominium 		442 3 08/05/2017 04:35AM
Last Post by Dominium

Megatronics V2- Inverted end stop damage IC2 Attachments

by MRGiacalone2005 		1,103 11 08/01/2017 11:20PM
Last Post by Dust

Controlling Solenoid Valve signal

by JoshuahMG 		289 4 07/28/2017 06:57PM
Last Post by VDX

Hot End Temperature Not Reading Accurately Attachments

by redhatman 		11,175 12 07/22/2017 05:48PM
Last Post by gbond

[dumb question] Turn on fans at a certain current?

by pugzor 		283 6 07/20/2017 01:32AM
Last Post by o_lampe

Rambo Mini issue

by sTon 		546 7 07/14/2017 07:28AM
Last Post by sTon

AZSMZ 12864 LCD + ESP8266 (ESP3D) Attachments

by cxandy 		865 1 07/12/2017 10:13PM
Last Post by cxandy

is RADDS not open source?

by ekaggrat 		1,628 20 07/12/2017 07:04PM
Last Post by VDX

Printer not reading SD card / bad connection between controller and LCD screen

by Maggie_at_OESH 		276 2 07/11/2017 01:49PM
Last Post by Maggie_at_OESH

Rambo 1.3 board extruder motor stutter

by kutch2001 		1,498 12 07/06/2017 11:45AM
Last Post by thomaaa

3DTouch and reprap firmware

by BramV 		419 2 07/01/2017 02:27PM
Last Post by dc42

newbie setting up the MKS Sbase...confused smiley

by jetboy1 		562 5 06/28/2017 05:21AM
Last Post by jetboy1

BL Touch and BIQU MKS-BASE V1.5 Plate Controller Board Attachments

by panadar 		1,180 2 06/28/2017 05:14AM
Last Post by Kruemel33

PCB manufacturing with a LCD layermask, possible?

by ElectricMucus 		2,613 7 06/21/2017 02:07PM
Last Post by altnelu

Controller LCD contrast issue   (Pages: 1 2)

by drhender 		24,659 42 06/21/2017 09:18AM
Last Post by carlonb

3D Touch z-probe and RADDS

by BramV 		665 5 06/19/2017 02:33PM
Last Post by BramV

Z max endstop issues

by bread_bird 		361 5 06/18/2017 02:55PM
Last Post by bread_bird

X Axis homing in wrong direction after hot end upgrade

by fullHundo 		328 1 06/18/2017 02:59AM
Last Post by fullHundo

Make a Drive By Wire Circuit Control System

by display 		308 3 06/17/2017 02:09AM
Last Post by o_lampe

how to upload firmware to melzi v2 board? Attachments

by kkwong1951 		4,513 9 06/16/2017 03:08AM
Last Post by DenisSh

Image 2 LCD

by 762x51 		701 2 06/12/2017 09:29AM
Last Post by 762x51

Problem Arduino Due and REPRAP_DISCOUNT SMART CONTROLLER LDC

by Italia 		423 3 06/02/2017 07:21AM
Last Post by Italia

Can you identify this connector? Attachments

by fullHundo 		401 3 05/31/2017 10:49PM
Last Post by fullHundo

Geetech GT2560 + TMC2208 Drivers

by OutcastZeroOne 		981 2 05/31/2017 10:15PM
Last Post by Traveler0612

TFT28 Not seeing GCODE files

by jtreg 		347 2 05/25/2017 09:40AM
Last Post by PhantomGT
Page 4 of 78    Pages: Previous12345NextLast