Show all posts by user
People building or using RepRaps.
Re: 3D printer running on 24V with RAMPS 1.4 or RAMPS 1.6 - 30 days ago
I agree. Though if you are going to boldly continue this course then search threw my posts you will see how I rewired my Arduino MEGA 2560 and RAMPS1.6 to work using a 24v supplyby Roberts_Clif - Safety & Best Practices
Re: Compiling and uploading marlin 2.1.3 - 4 weeks ago
Wow would forever grateful to see this code. as I have been asking to do something really close to what you just completed.by Roberts_Clif - Firmware - Marlin
Re: Anycubic Kobra 3 Combo - 4 weeks ago
After Many months accidentally upgraded my Anycubic 3 Kobra firmware today. Will have to wait till prints finishes to ascertain my current firmware version. It appears to be working correctly so glad this is over and done with. 3D Printing more of the Dino bag clips, and a someone that would like a few. I have the speed set high enough that a clip only takes about an hour to successfully printsby Roberts_Clif - Prusa i3 and variants
Re: Help compiling for ender 3 - 6 weeks ago
I hate to see users with broken 3D Printers or computers, though with a computer how in the world can you survive. Though I found this information online. You can use a third-party app like ArduinoDroid to program Arduino boards with an Android device. This requires installing the app, connecting your phone to the Arduino board via a USB OTG cable, and using the app's built-in editor to writeby Roberts_Clif - Firmware - Marlin
Re: feed back on calibration tool needed - 3 months ago
I think it is great ideal, though I have not tested it yet.by Roberts_Clif - General
Re: feed back on calibration tool needed - 3 months ago
Well thank you. Before I print my next models I will see how it works.by Roberts_Clif - General
Re: How to configure real position of endstop - 3 months ago
Then what I did was to make some adjustable end stop mounts so when activated position is correct.by Roberts_Clif - Reprappers
Re: Marlin Simulator Help - 3 months ago
I too just learned of this simulator, though Will try it in Windows 11 Pro version 10.0.26100 Build 26100. Just need to read the full article several times to determine what I need to do for Marlin Simulator setup in Windows 11 to execute the program correctly.by Roberts_Clif - Firmware - Marlin
Re: The extruder motor doesn't work - 4 months ago
This may or may not be your problem though until hot-end get to a set temperature the extruder will not extrude to protect itself. Specifically, you'll modify parameters related to minimum and maximum temperature limits, thermal runaway protection, and potentially cold extrusion prevention. #define PREVENT_COLD_EXTRUSION #define EXTRUDE_MINTEMP Defines the minimum temperature which the extrudeby Roberts_Clif - Reprappers
Re: Forum totally dead? - 4 months ago
I was starting to build a CoreXY 3D printer though with the purchase of a pair of Anycubic Kobra 3's decided to turn it into a smaller version of my MPCNC. Though like I say it is just too hot here, yesterday when temperature hit 106 with all the AC's running the inside went to 86. I know that the Kobra 3 combos were so cheap that I could purchase the parts for the price for a DIY. Though my MPby Roberts_Clif - CoreXY Machines
Re: Forum totally dead? - 5 months ago
I am here every day though the temperature is way too high to add any extra heat inside this old house. so nothing to post really.by Roberts_Clif - CoreXY Machines
Re: Errors in Marling while compiling in PlatformIO - 5 months ago
It is all good, glad to see your learning how to configure Marlinby Roberts_Clif - Firmware - Marlin
Re: where do I find these files? - 5 months ago
I googled them and found this indirection.cpp.d trinamic.cpp.dby Roberts_Clif - Firmware - Marlin
Re: Errors in Marling while compiling in PlatformIO - 5 months ago
Post your Marlin source I will take a look to see why it errors.by Roberts_Clif - Firmware - Marlin
Re: Errors in Marling while compiling in PlatformIO - 5 months ago
Look at these lines Search google with this line Marlin firmware enable Advanced_Pause and the Nozzle_Park or this line Marlin firmware enable Advanced Pause and the Nozzle Parkby Roberts_Clif - Firmware - Marlin
Re: Leapfrog Bolt Pro - 6 months ago
I found this Leapfrog web site on my first search, 1st page opened. It appears to have most of the information you should need.by Roberts_Clif - General
Re: TR8X4 Lead screw tension nut - 6 months ago
That was very smart ! thank for the informationby Roberts_Clif - Mechanics
Re: TR8X4 Lead screw tension nut - 6 months ago
Started with a 8X8 lead screw to I decided to try the 8X2 shown in below Highlighted in Green. // Typical stepper motors have 200 steps per full step/rev = 1.8°/step, so 1/16 microstepping = STEPS_PER_REVOLUTION_E = 3200 // X-Y Axis 3200, / 20 tooth, / 2mm pitch = 200*16 / 20 / 2 = 80 :: (STEPS_PER_REVOLUTION_X / IDLER_TEETH_X / BELT_PITCH_X) // Z Axis 3200, / 1.25mm pitch leadscrew = 200*16 /by Roberts_Clif - Mechanics
Re: Tinybee z offset - 7 months ago
Did a web search for " Tinybee Z offset enable baby-stepping" Found this information may of may not help, though thought I would post anyway. QuoteAI Overview While the MKS Tinybee board itself doesn't natively support live babystepping, meaning you can't directly adjust the Z-offset while a print is in progress. You can still utilize babystepping to make permanent Z-offset adjustments by integby Roberts_Clif - Firmware - Marlin
Re: Anycubic Kobra 3 Combo - 8 months ago
I found a work around. If you load your model into Bambu Studio create all the Painted surfaces and save to 3MF file Reload model into Orca Slicer 2.3.0-RC change to your Kobra 3 and filament profiles slice and save to USB flash drive then print with Kobra 3.by Roberts_Clif - Prusa i3 and variants
Re: Anycubic Kobra 3 Combo - 8 months ago
Hi I have been looking for a users manual for Orca Slicer 2.3.0 or anything even close as to allow me to use the full potential of slicers. Would be happy to see this in any form pdf, you-tube videos just would like to learn everything that can be done with this slicer.by Roberts_Clif - Prusa i3 and variants
Re: Anycubic Kobra 3 Combo - 8 months ago
Here we have a Painted object shown in the photo below. If the Painted is in Object mode then they will have a place to select/change the filament. Painted Object Else if they do not have, then the filament will not change in this global mode.by Roberts_Clif - Prusa i3 and variants
Re: Anycubic Kobra 3 Combo - 8 months ago
Yesterday Well thought is would work simply because Orca Slicer 2.3.0 RC lists AnuCubic Kobra 3 in compatible Printers lists. I guess in a way it does work because it will print a mono print though not a multiple color model. OK back to looking for a better slicer for my Anycubic Kobra 3 combo. __________________________________________________________________________________________ OK todayby Roberts_Clif - Prusa i3 and variants
Re: ADVANCED_PAUSE_FEATURE for X,Y,Z move - 9 months ago
In configuration.h #define NOZZLE_PARK_FEATURE #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z } #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } #define NOZZLE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis) #define NOZZLE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta priby Roberts_Clif - Firmware - Marlin
Re: ADVANCED_PAUSE_FEATURE for X,Y,Z move - 9 months ago
Example of my pause code #define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. // This short retract is done immediately, before parking the nozzle. #define FILAMENT_CHANGby Roberts_Clif - Firmware - Marlin
Re: Kobra3 Combo Error 10242 - 9 months ago
Anycubic Slicer Next 1.3.3 For Windows What's new: 1. Added "Skip Part" feature (Currently for S1, version ≥2.8.4.3) 2. Improved login region prompts. 3. Fixed temperature errors when leveling with multi-color filament box. 4. Enhanced overhang printing quality 5. Added support for Anycubic Kobra 3 Max and new filament profiles: PLA Silk @Anycubic Kobra S1 PLA Luminous @Anycubic Kobra S1 PLA Silby Roberts_Clif - FAQ - Bei Problemen und allgemeinen Fragen ...
Re: Geeetech I3 Pro B problems after updating - 9 months ago
Quotetag1260 Is the configure h file the same from version to version or do you need to write a new one every update? The Configuration.h file varies form version to version. I use Winmerge to compare both files. Winmerge allows you to compare two or even three files then make changes to them and save any or all. In fact it is probably time to see what the next version of winmerge has to offer.by Roberts_Clif - Prusa i3 and variants
Re: Geeetech I3 Pro B problems after updating - 9 months ago
This is good. If you have any more questions will be here just post.by Roberts_Clif - Prusa i3 and variants