Welcome! Log In Create A New Profile

Advanced

Extruded Aluminum Frames

Cartesian XYZ machines with frames made of extruded aluminum, T-Slot, Makerslide, and more. See http://reprap.org/wiki/Category:Aluminum. Previously named "Extruded Aluminum"  
Page 1 of 5    Pages: 12345Next
Forum List New Topic RSS
Subject Views Posts Last Post

MechaBits KraftWerk'r   (Pages: 1 2 3)

by MechaBits 		9,297 90 02/20/2019 01:26AM
Last Post by MechaBits

Building a 3d printer - looking for some suggestions

by Cougar281 		276 7 02/06/2019 12:14PM
Last Post by Cougar281

Beware : Extruded profiles can be bended or twisted, while remaining standard !

by M_Xeno 		176 4 02/04/2019 03:33PM
Last Post by gmedlicott

y carriage for mk3 4030 heatbed?

by emaayan 		84 1 02/01/2019 06:59AM
Last Post by emaayan

Carbon tubes --> longer then 1 meter

by Arnix 		151 1 01/23/2019 09:32AM
Last Post by Arnix

Linear Rail Cantilever printer build Attachments

by awratten 		504 9 12/30/2018 07:58PM
Last Post by awratten

Connecting extruded aluminium?   (Pages: 1 2 3)

by Treito 		14,169 70 12/29/2018 06:18PM
Last Post by Ed3D

Belt z axis - which gears?

by witor 		325 8 12/20/2018 12:48PM
Last Post by witor

Sources for extruded aluminum profiles   (Pages: 1 2)

by MarcusWolschon 		13,296 35 12/19/2018 05:13PM
Last Post by witor

4040 Open build profiles right angle joint - what's the best way? Attachments

by witor 		207 3 12/19/2018 04:35PM
Last Post by witor

1 or 2 rails for y axis?

by witor 		287 13 12/17/2018 08:06PM
Last Post by witor

Rep A Sketch Attachments

by Number_5 		386 10 12/01/2018 09:45PM
Last Post by Number_5

Printer Design with Bearings on Extrusions

by gmedlicott 		348 12 11/29/2018 01:20PM
Last Post by gmedlicott

Three point bed adjustment

by charlieRC 		422 20 11/11/2018 12:58PM
Last Post by charlieRC

Ender 3 vs Malyan M150 (Wanhao i3 look-a-like)

by SaleB 		318 2 11/10/2018 11:18AM
Last Post by Number_5

First build, having issues Attachments

by LFG 		435 13 10/20/2018 10:05PM
Last Post by Dust

MiniMax: my experimental CoreXY Attachments

by o_lampe 		704 9 09/23/2018 02:14AM
Last Post by o_lampe

Cutting extruded ali

by nod2 		486 9 09/03/2018 07:07AM
Last Post by mcdanlj

X-axis Not homing after crash Flsun i3

by dolon 		245 2 08/11/2018 02:24AM
Last Post by dolon

Black Beauty Build Log   (Pages: 1 2)

by gtj 		2,198 50 07/19/2018 07:21PM
Last Post by gtj

Cutting Aluminum Extrusion By hand

by Falcondestroyer123 		3,637 19 06/27/2018 08:53AM
Last Post by Bluemonkey

Scrap yard run.... SCORE! Attachments

by the_digital_dentist 		564 5 06/17/2018 11:26PM
Last Post by the_digital_dentist

HyperCube OverKill Build Log   (Pages: 1 2)

by gtj 		8,567 35 05/24/2018 10:32AM
Last Post by gtj

Which side does the end-stops goes?

by lunar211 		972 7 05/17/2018 01:49PM
Last Post by the_digital_dentist

Leadscrew driven XY gantry printer?

by klcjr89 		1,779 12 03/25/2018 05:20PM
Last Post by gtj

Cheap-and-cheerful Taobao $150 knock-off running at 200mm/sec   (Pages: 1 2 3)

by lkcl 		4,297 80 01/05/2018 10:33PM
Last Post by lkcl

RepRap Tevo Tornado/Cr-10

by masterviana 		892 3 12/28/2017 06:28AM
Last Post by masterviana

Unable to complete my Tarantula due to dodgy parts!

by cheapo 		789 3 12/23/2017 09:59AM
Last Post by cheapo

FLSUN I3 kit review   (Pages: 1 ... 4 5 6)

by R.G. 		27,233 159 12/20/2017 08:54AM
Last Post by jnsbanman

flsun metal frame: configure.h

by wrapperz 		1,700 3 10/26/2017 01:19AM
Last Post by wrapperz
Page 1 of 5    Pages: 12345Next