Welcome! Log In Create A New Profile

Extruded Aluminum Frames

Cartesian XYZ machines with frames made of extruded aluminum, T-Slot, Makerslide, and more. See http://reprap.org/wiki/Category:Aluminum. Previously named "Extruded Aluminum"

Page 2 of 5 Pages:

123 4 5

Forum List New Topic RSS

	Views	Posts	Last Post
help identifying controller board by wrapperz	909	3	10/18/2017 06:37PM Last Post by wrapperz
Prusa i3 MK3 extrusion by Dust	3,645	12	10/04/2017 08:28AM Last Post by MechaBits
Riki200 (Pages: 1 2 3 4 5) by lkcl	5,671	123	09/11/2017 12:39AM Last Post by lkcl
Z-axis homing not repeatable (prusa i3 from FLSUN) by meekeech	1,154	1	08/17/2017 02:09AM Last Post by meekeech
Z Axis Resets 15mm Above Bed by dolon	692	3	08/15/2017 01:54AM Last Post by dolon
My first Servo motor based 3d printer by vova	18,526	24	08/03/2017 02:23PM Last Post by 691175002
linear rails advice for a 200x200 design by lkcl	1,819	6	06/13/2017 06:15AM Last Post by chris33
New build, pre-design questions, extrusions, shafts, dimensions, electronics by SaleB	2,034	20	05/16/2017 07:22AM Last Post by lkcl
This is a tank by cwaa	2,676	10	05/15/2017 10:58AM Last Post by cwaa
Help me improve rigidity of frame by karandex	3,167	8	05/12/2017 01:01PM Last Post by lkcl
Where to get 20x20mm aluminum extrusion (Pages: 1 2) by Doug1	23,490	37	05/02/2017 11:53AM Last Post by robb_nl
Why is V-slot so much more expensive than T-slot by Antscran	3,045	6	04/27/2017 04:03PM Last Post by cwaa
cutting 8020 extrusions with a chop saw by davedavedave	3,547	7	04/19/2017 05:50PM Last Post by cwaa
New FlyingBear P902 issue by Carl_S	1,098	2	04/17/2017 08:41AM Last Post by Carl_S
End Stops? by Rlewisrlou666	1,316	4	03/23/2017 09:33AM Last Post by the_digital_dentist
FLSUN i3 Filament changeover by wunderkind	1,126	1	03/22/2017 04:45PM Last Post by wunderkind
Quadmax - a Mendelmax conversion by Chri	1,412	1	12/28/2016 04:52AM Last Post by Chri
Anodised Extruded Aluminium. by Rlewisrlou666	1,382	4	10/19/2016 12:32PM Last Post by Rlewisrlou666
Duet board wont connect to panelDUE and endstops by 1andchin	1,750	9	09/06/2016 06:02AM Last Post by DjDemonD
Mechanical End Stop Wiring Issue Mks 1.4 Board by ca_resh	2,746	3	09/01/2016 04:46PM Last Post by ca_resh
First Printer, 225mm^3 printer / mill combo build (Pages: 1 2 3 4) by Tired2	13,096	100	08/09/2016 11:47AM Last Post by Tired2
Score another one for the Openbuilds by Shank man	1,508	5	08/09/2016 05:38AM Last Post by Shank man
POC printer by deckingman	1,488	6	07/21/2016 02:49PM Last Post by deckingman
New to this part of the forum by wampablo	1,069	1	07/13/2016 03:42PM Last Post by wampablo
My advice on buying Open Builds Vslot in UK by deckingman	2,985	23	07/13/2016 02:05PM Last Post by RyanL
Print bed printing down as aposed to printing up by johnvictor	1,072	1	07/11/2016 11:44AM Last Post by johnvictor
Building Questions by ollyreprap	916	6	07/02/2016 04:12PM Last Post by deckingman
Vertical Lines on my prints by juanfly	1,197	5	06/28/2016 05:43AM Last Post by Origamib
[BuildLog] HexRap \| Extrusion based 3D-Printer by TheHexaCube	1,323	6	06/06/2016 07:45PM Last Post by Origamib
Measurements of Misumi 2020 and Hiwin MGN12 by FA-MAS	1,632	8	05/29/2016 05:21PM Last Post by Mikk36

Page 2 of 5 Pages:

123 4 5

Extruded Aluminum Frames

Riki200 (Pages: 1 2 3 4 5)

Where to get 20x20mm aluminum extrusion (Pages: 1 2)

First Printer, 225mm^3 printer / mill combo build (Pages: 1 2 3 4)