Welcome! Log In Create A New Profile

RepRap Usergroup - Argentina

http://reprap.org/wiki/RUG/Argentina - Lista de proveedores, Reuniones, y ayuda al futuro RepRapper

Page 31 of 37 Pages:

29 303132 33

Forum List New Topic RSS

	Views	Posts	Last Post
Problema con medidas by layoroa	747	7	03/28/2014 04:56PM Last Post by layoroa
ABS delamination by patriciorivera	932	5	03/28/2014 09:22AM Last Post by patriciorivera
nos juntamos? by patriciorivera	926	23	03/25/2014 05:51PM Last Post by epoxi
Falla en determinados layers de la pieza by layoroa	908	15	03/23/2014 09:42AM Last Post by ChArDoN
BigRep by patriciorivera	893	15	03/21/2014 03:51PM Last Post by Pointless
Marco y base - Prusa i3 single frame by josemm	2,182	23	03/20/2014 12:29PM Last Post by GAZ082
Problemita de impresion by ChArDoN	1,493	22	03/19/2014 05:14PM Last Post by DVDBA
Recomendaciones Material de Soporte by layoroa	573	1	03/18/2014 05:46PM Last Post by layoroa
Consulta, movimiento del motor by marcos.capra	778	10	03/17/2014 03:17PM Last Post by Risher
Fuente (Pages: 1 2) by pelta	2,133	34	03/17/2014 10:23AM Last Post by aleiovanevcp
Drivers A4988 o 8825pro? by aleiovanevcp	1,049	6	03/16/2014 07:22AM Last Post by aleiovanevcp
Problema Borde Cubo by elaerico	800	8	03/15/2014 02:14PM Last Post by jameghino
Problema con Arduino - "Puerto COM5 ya esta en uso" by josemm	18,290	14	03/15/2014 12:15AM Last Post by josemm
Mendel en Rosario (Pages: 1 2 3) by luismanson	3,031	81	03/13/2014 03:36PM Last Post by luismanson
Impresiones al reves!... by layoroa	826	5	03/12/2014 07:20PM Last Post by jameghino
Prusa i3 Rework (Pages: 1 2) by ChArDoN	5,475	48	03/12/2014 07:19PM Last Post by jameghino
extrusor "goteo constante" by Pablo	3,361	10	03/12/2014 02:00PM Last Post by jameghino
[Problema] Temperatura Ramps 1.4 by Charlitos85	1,045	10	03/10/2014 10:28AM Last Post by Charlitos85
VERSUS by totodominguez	507	3	03/07/2014 09:36AM Last Post by ChArDoN
Vibracion al hacer circulos by Pointless	1,155	7	03/07/2014 09:05AM Last Post by Pointless
Nace una I3 en Rosario by arquitron	1,032	23	03/06/2014 05:28PM Last Post by Pointless
Foreros de córdoba! y cuasi presentación by makymaldonado	661	2	03/04/2014 07:22PM Last Post by aleiovanevcp
Novato Prusa I3 by Josleon100	7,237	21	03/03/2014 09:37PM Last Post by josemm
Refrigeración Activa Hot-End Argento. by layoroa	740	3	03/02/2014 05:57PM Last Post by Isamu2040
Recalentamiento en RAMP 1.4 by Charlitos85	648	7	02/28/2014 01:13AM Last Post by Charlitos85
Problema de Impresion con Clip by puche	828	9	02/25/2014 01:13PM Last Post by SinapTec
Rentabilidad by totodominguez	2,067	10	02/22/2014 03:36PM Last Post by SinapTec
Problemas con LCD by ChArDoN	548	4	02/19/2014 05:50PM Last Post by ChArDoN
Boludeando un poco by Isamu2040	1,071	9	02/18/2014 12:18AM Last Post by luismanson
¿Hotends todo metal? by jameghino	968	5	02/16/2014 02:30PM Last Post by robbyg

Page 31 of 37 Pages:

29 303132 33

RepRap Usergroup - Argentina

Fuente (Pages: 1 2)

Mendel en Rosario (Pages: 1 2 3)

Prusa i3 Rework (Pages: 1 2)