Welcome! Log In Create A New Profile

Advanced

Firmware - mainstream and related support

Subject Views Posts Last Post

Extruder stepper rapid oscillations (Sprinter)

by Edon
1,104 2 02/08/2012 08:03AM
Last Post by VDX

Heat and false temperature reading

by Kalle
728 1 02/04/2012 03:33PM
Last Post by Kalle

Heat but no temperature reading!

by Rico
915 3 02/04/2012 07:30AM
Last Post by Kalle

Sprinter uploads then turns the extruder

by roygpa
816 3 02/03/2012 03:26PM
Last Post by jezmy

Changing from FiveD firmware to Marlin - A few questions about configuration.h values Attachments

by Flackster
2,030 4 02/02/2012 07:45AM
Last Post by Flackster

PCB Heatbed

by windcatcher
3,012 11 01/28/2012 04:14AM
Last Post by Traumflug

arduino 1.0 and sprinter

by dissidence
1,952 4 01/28/2012 03:04AM
Last Post by windcatcher

Y axe (only one direction)

by DrimIsen
1,003 2 01/25/2012 10:28AM
Last Post by rhmorrison

Axis stops moving after G91

by _Alex_
670 1 01/22/2012 06:16AM
Last Post by _Alex_

Negative X,Y,Z values allowed?

by misan
2,244 3 01/20/2012 02:56AM
Last Post by misan

[solved] cant move z with sprinter firmware

by zg_bot
1,134 8 01/12/2012 12:01AM
Last Post by zg_bot

Z axis not working with Marlin

by miro87043
1,736 3 01/11/2012 05:57PM
Last Post by Ben Howes

Prints stop after some unknown number of commands

by dazed.dnc
1,932 27 01/11/2012 11:24AM
Last Post by jamesdanielv

Speed differences in Sprinter

by Albert384
1,588 6 01/11/2012 10:54AM
Last Post by jamesdanielv

Axis unable to change directions

by TheWyliestCoyote
1,077 3 01/10/2012 10:45PM
Last Post by TheWyliestCoyote

Is there an Idiots guide to programming the Arduino?

by Chompalot
1,124 5 01/04/2012 02:14PM
Last Post by Chompalot

Sanguinololu 1.3A, Sprinter (latest from git) no extruder

by javanree
1,811 10 01/03/2012 02:26PM
Last Post by javanree

serial lcd

by dissidence
1,163 5 01/02/2012 08:29AM
Last Post by dissidence

Sprinter firmware, All 3 axis going twice the distance

by QFE24
1,593 4 01/01/2012 05:53PM
Last Post by martinprice2004

RepRap Software Wont Open With Gen 6

by andy_tratter
1,117 4 12/24/2011 07:03PM
Last Post by Codebreaker

Y skips with marlin not sprinter Attachments

by ambiguousphoton
1,372 5 12/24/2011 05:17AM
Last Post by Traumflug

Gen7 and Teacup Config.h setup check

by foshon
1,169 3 12/20/2011 04:39AM
Last Post by foshon

Homing direction on a Mendel/ FiveD firmware

by hessel_swart
901 2 12/16/2011 06:08AM
Last Post by Traumflug

Can't compile FiveD

by dfrancis750
1,346 6 12/09/2011 09:22AM
Last Post by dfrancis750

Sprinter/fastio.h question

by RobertB
938 1 12/08/2011 10:51PM
Last Post by RobertB

Firmware nightmare, 5D, Sprinter, oh my

by Vortex87
927 2 12/08/2011 03:43AM
Last Post by Traumflug

plus side endstop issues

by chicht
775 2 12/02/2011 12:05PM
Last Post by x2800m

Gen 7 Teacup axis movements stops, extruder runs reverse

by madmaxx
1,300 11 11/29/2011 06:59PM
Last Post by madmaxx

Mainstream vs Experimental

by brnrd
830 1 11/25/2011 08:26AM
Last Post by brnrd

GEN6 firmware seems to upload but no changes are reflected Attachments

by Flackster
1,830 23 11/23/2011 05:49PM
Last Post by viseng