Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Subject Views Posts Last Post

Delta calibration Attachments

by frankvdh
305 2 04/29/2018 03:06PM
Last Post by frankvdh

Anycubic Kossel Linear Plus and "periodic surface marks"

by Andriee
283 3 04/28/2018 09:37AM
Last Post by GER776

Two rods on one (Delrin-) ball-effector

by o_lampe
690 28 04/28/2018 04:01AM
Last Post by o_lampe

G33 P2 running off the bed

by Corbid
349 3 04/25/2018 02:16PM
Last Post by grtyvr

G33 in a anycubic delta probe outside bed, and on a side...

by marcottt
198 2 04/19/2018 02:31AM
Last Post by LVD

Do delta machines still print in flat layers/slices?

by richard the boffin
401 5 04/11/2018 01:31PM
Last Post by Origamib
This topic has been moved.

Additional fan on Duet board 0.6

by swaroop
    This topic has been moved.

board problem

by Lc1975
261 3 04/06/2018 05:31AM
Last Post by Lc1975

Anycubic kossel plus Attachments

by lazos1996
475 4 04/02/2018 04:52PM
Last Post by dc42

Z-Banding Anycubic Kossel Linear Attachments

by rigs
323 3 03/31/2018 07:56AM
Last Post by dc42

Haydns printed Mag Rods improved Attachments   (Pages: 1 2)

by o_lampe
1,681 60 03/30/2018 06:42PM
Last Post by frankvdh

Beginner's questions about a custom delta design

by RoGeorge
443 21 03/27/2018 07:09PM
Last Post by dc42

Marlin vs. Repetier on a delta printer

by ruevs
736 11 03/26/2018 06:32AM
Last Post by hercek

Making PTFE cups for magnetic rods

by gambrose
532 23 03/24/2018 02:56PM
Last Post by ruevs

Standardised hot-end connector

by frankvdh
360 5 03/22/2018 08:54AM
Last Post by DjDemonD

Stupid idea or not?? Attachments

by Nitram
325 3 03/21/2018 03:28PM
Last Post by Nitram

Suggested carriages and effector for Haydn magnetic arms for Kossel Mini?

by JohnOCFII
669 10 03/18/2018 10:21AM
Last Post by JohnOCFII

New delta design with fixed ballscrews

by klcjr89
630 26 03/10/2018 03:37PM
Last Post by klcjr89

Modification d'une imprimante 3D Geeetech Rostock 301 dysfonctionnelle !   (Pages: 1 2)

by L'ami René
2,369 37 03/09/2018 02:33PM
Last Post by L'ami René

Trying to use 7-factor calibration on Delta with Convex Deformation.

by Lobotomy
337 16 03/09/2018 02:41AM
Last Post by DjDemonD

DemonDeltaTube - A delta inside an acrylic tube... Build Attachments   (Pages: 1 2 3 4)

by DjDemonD
2,782 93 03/09/2018 02:20AM
Last Post by DjDemonD

Ugly First Layer on Anycubic Linear Plus Attachments

by Kunj
460 3 03/07/2018 11:54AM
Last Post by eyebee

High and low spots on delta print bed - need help and advice.

by Olaf188
270 5 03/05/2018 05:46PM
Last Post by Olaf188

Anycubic kossel extruding in the air

by frazercampbell
440 4 03/05/2018 03:58AM
Last Post by kubik256

Carbon rods: 6mm solid or hollow 10mm dia?   (Pages: 1 2)

by o_lampe
647 36 03/04/2018 01:43PM
Last Post by hercek

Need help setting up Delta Smart Effector in RRF.

by Lobotomy
452 9 03/01/2018 05:22PM
Last Post by Lobotomy

Anycubic Kossel Plus try to level outside bed area

by masterviana
614 9 03/01/2018 08:27AM
Last Post by kubik256

Delta sizing?

by JanJoh
441 14 02/28/2018 03:56PM
Last Post by JanJoh

effector leveling

by deaconfrost
317 8 02/27/2018 01:04PM
Last Post by Haydn

DIY Kossel XL prints too small... And flying extruder question Attachments

by Archiclem
325 7 02/27/2018 01:01PM
Last Post by Haydn