Welcome! Log In Create A New Profile

Advanced

Estrusori, Hotends, Heated bed, Filamenti, etc.

Sezione dove discutere di materiali di stampa e delle parti calde della nostra stampante 3D. Estrusori, Hotends, Heated bed, trafilatura e materiali (filamenti ABS/PLA/etc) 
Subject Views Posts Last Post
Sticky

►►►► LINEE GUIDA E REGOLE PER UN USO CORRETTO DEL FORUM ◄◄◄◄ Da leggere! Segnalate ai moderatori le discussioni da chiudere - LE REGOLE VANNO LETTE E APPLICATE!

by Gordie
1,519 1 03/09/2014 08:26AM
Last Post by Gordie

upgrade estrusore Attachments

by il_donv
48 1 04/12/2019 10:06AM
Last Post by il_donv

Riscaldamento piatto 220V vs 24V

by claustro
55 2 04/04/2019 05:53PM
Last Post by onekk

Filamento amazon basics

by Unky3d
109 2 03/13/2019 06:58PM
Last Post by Stepper79

adesivo per piano

by snowmax
196 4 03/06/2019 07:16PM
Last Post by Aldebaran94

riduttore per estrusore 3,5:1

by Stepper79
80 1 03/05/2019 11:37AM
Last Post by Stepper79

Problema esttusore con Petg   (Pages: 1 2 3)

by filofilato
676 62 02/22/2019 07:32AM
Last Post by bilanciamist

PLA+/PLA Plus

by iLMario
176 12 02/18/2019 11:17AM
Last Post by laudix

Hotend XCR-BP6 qualcuno lo usa? Attachments

by sinimar
144 11 02/15/2019 11:09AM
Last Post by alil2096

TITAN AERO consiglio

by ADRIANO3D
288 3 02/14/2019 06:02AM
Last Post by alex27riva

scarto filamento

by agospaolo89
129 3 01/23/2019 03:16PM
Last Post by agospaolo89

Estrusore fino a 350° per PEEK

by peppeleo3006
176 3 12/31/2018 02:20AM
Last Post by peppeleo3006

THERMAL_PROTECTION:1

by filofilato
135 6 12/18/2018 12:49PM
Last Post by onekk

Materiale elastico

by filofilato
193 6 12/16/2018 02:16PM
Last Post by Mr Yod

temperature estrusore scende durante la stampa

by Bong313
238 6 12/04/2018 05:33AM
Last Post by Alberto70

Piatto a tre viti?

by filofilato
221 10 11/13/2018 06:51AM
Last Post by onekk

Errore temperatura -72°

by mga
135 8 11/06/2018 06:19AM
Last Post by onekk

Scelta estrusore per Prusa i3 Pro B

by Suchigno
294 14 11/05/2018 02:09AM
Last Post by Luca_Benedetto

Problemi di Alimentazione?

by Foxcat62
244 8 10/30/2018 06:39AM
Last Post by onekk

3mm (soggetto semplice, mica siam tutti scrittori)

by mr.krash
248 7 10/25/2018 03:10AM
Last Post by alil2096

PLA 3D870 - PLA ad alte prestazioni

by laudix
185 1 09/04/2018 11:46AM
Last Post by laudix

dubbio su pulizia ugello microswiss mk10

by losco
266 22 09/03/2018 06:29AM
Last Post by losco

[Modello STL] Supporto per E3D Titan su Geeetech i3 Pro B Attachments

by Noisemaker
902 12 08/29/2018 10:59AM
Last Post by dobler

rottura e manutenzione migliorativa MK8 direct

by Aldebaran94
375 24 08/06/2018 10:52AM
Last Post by AndreaMattiaDenaro

E3dv6 Raffreddamento a liquido   (Pages: 1 2)

by Stepper79
552 33 08/05/2018 07:23PM
Last Post by Stepper79

Ho un estrusore MK8 direct. Se accorcio la cold end di 10mm la dissipazione peggiora?

by Aldebaran94
205 6 07/22/2018 01:43PM
Last Post by onekk

Andare oltre i 260°   (Pages: 1 2)

by AndreaMattiaDenaro
805 59 06/25/2018 07:46AM
Last Post by Gordie

PETG... sostituirà veramente l'ABS???   (Pages: 1 ... 4 5 6)

by Felixmau
2,211 155 06/25/2018 05:57AM
Last Post by Gordie

Stampante Geeetech non estrude

by Pinguto
153 5 06/22/2018 09:42AM
Last Post by onekk

Rampa di riscaldamento Heated bed a 105°C lenta

by davgiuffrida
412 10 06/17/2018 04:53PM
Last Post by Stepper79

Problema riscaldamento heat bed

by giuseppe_reprap
146 2 06/16/2018 11:11AM
Last Post by onekk