Welcome! Log In Create A New Profile

CoreXY Machines

http://reprap.org/wiki/CoreXY

Page 15 of 20 Pages:

Forum List New Topic RSS

Subject		Views	Posts	Last Post
	Z bed cantilever by MatthewHall	1,133	7	07/02/2016 02:41PM Last Post by DjDemonD
	CoreXY Dbot building by vpt5566	7,995	29	07/01/2016 02:42PM Last Post by KDan
	SmartrapCore Question by engmaster	1,126	23	07/01/2016 12:52PM Last Post by lkcl
	perfil extrusionado 2040 by skafotrabo	572	2	06/27/2016 11:54AM Last Post by Velric
	Corexy issues advice needed by rastaman46	3,430	29	06/27/2016 03:50AM Last Post by rastaman46
	Servo motor 3d printer ver.2 H-Bot setup by vova	2,642	13	06/21/2016 10:00PM Last Post by ttttttokkk
	Triple-rod supported bed, 8mm shaft enough or go higher? by realthor	1,291	30	06/11/2016 06:46PM Last Post by realthor
	Foldable, portable CoreXY (Fusebox derivative) (Pages: 1 2 3 4 5) by lkcl	5,459	138	06/10/2016 07:22AM Last Post by lkcl
	Would a hybrid Horizontal-Vertical XCarriage bring any advantage? by realthor	595	6	06/09/2016 09:04AM Last Post by realthor
	Corexy Z prob Marlin by rastaman46	596	1	06/07/2016 03:45AM Last Post by rastaman46
	Speeds / Config by PDBeal	3,202	15	06/06/2016 05:43PM Last Post by dc42
	My new CoreXY completed build- Issues by Vigilant	1,860	6	06/06/2016 08:21AM Last Post by LarsK
	Duet bed heater problem by appjaws1	465	4	06/04/2016 05:45PM Last Post by dc42
	Folgertech FT-5 by Kurzaa	898	2	06/03/2016 11:38PM Last Post by cozmicray
	Using Z stop for homing - help by appjaws1	552	5	06/03/2016 09:04AM Last Post by dc42
	end stop switches with duet board by appjaws1	5,198	10	06/02/2016 12:13PM Last Post by blt3dp
	Why does this design of pulley used less in Corexy by faith	981	4	06/02/2016 08:00AM Last Post by filipeCampos
	Quick heated bed question by deckingman	435	3	06/01/2016 06:22PM Last Post by deckingman
	CoreXY or Moving Bridge with fixed bed which way to go for large parts by rxpu99	2,192	8	05/20/2016 04:05PM Last Post by lkcl
	New COREXY Design loosely based on Vulcanus Max v1.1 by thetekguy	2,356	11	05/20/2016 01:42PM Last Post by lkcl
	Corexy PCB mill???? by rastaman46	1,287	7	05/20/2016 05:11AM Last Post by VDX
	Is Nema17 1.2A too weak for 3d printing? (Pages: 1 2) by realthor	3,610	45	05/19/2016 01:06PM Last Post by cozmicray
	Corexy homing issue advice needed by rastaman46	688	12	05/19/2016 11:48AM Last Post by rastaman46
	What's the best placement of EndStops in a CoreXY and are mechanical ones still used by you guys? (Pages: 1 2 3) by realthor	5,481	66	05/18/2016 04:10PM Last Post by grat
	Vertical vs Horizontal X rods arrangement? What distance between rods? by realthor	3,926	9	05/18/2016 02:25PM Last Post by lkcl
	Vertical X-Rods vs Horizontal X-Rods in CoreXY by lkcl	3,491	15	05/18/2016 02:23PM Last Post by lkcl
	NEW CoreXY Design by MatthewHall	2,853	12	05/16/2016 02:42PM Last Post by blt3dp
	Do CoreXY belts need to be of equal tension? (Pages: 1 2) by realthor	11,781	36	05/16/2016 09:38AM Last Post by lkcl
	corexy with 2 or 3 direct drive extruders by hucilu	8,033	25	05/15/2016 12:06PM Last Post by hucilu
	Coffeetable CoreXY:: new build :: small apartment rep-strap solutions (Pages: 1 2 3 4 5) by realthor	12,370	137	05/14/2016 10:03AM Last Post by realthor

Page 15 of 20 Pages: